About roland.bellwald

roland.bellwald · 09-13-2011

Inbound PSTN calls arrive on the H.323 voice gateway IOS Version 12.15(1)T1 continue to the CUCM Version 8.5.1.12900-7 which signalls the call to the phones (8961 and 6941) with firmware 9.2(1).On the 8961 phones, the calls are displayed fine..."unkn...

roland.bellwald · 02-15-2010

To show real interoperability and integration, we enabled on a Cisco 28xx gateway IOS version 12.4(22)T the gatekeeper feature to register the video endpoint to and configured the same device to act as a gateway to do ISDN bonding with the connected ...

roland.bellwald · 06-09-2009

I believe HHC being a feature dependent on the phone firmware version. As it has to be enabled on CUCM, there came some doubts about my thinking and as I am unable to verify at the moment, I would like to ask if HHC being supported on Cisco Unified C...

roland.bellwald · 03-22-2007

Dear Community,I did configure the CallManager (4.2(3)) to dial out via overlap sending (Route Pattern: 0.00! "allow overlap sending" ticked). And the gateway 12.4(8)c as...voice service voip h323 h225 timeout t302 15 h225 signal overlap modem pass...

roland.bellwald · 09-22-2006

Dear Netpros,The callmanager appears not to have the proper username / password configured. We tried to use the ccmadministrator, a application user and end user account, but none of them worked properly.The documentation does not provide CCM5 specif...

roland.bellwald · 09-13-2011

Thanks a lot for the quick answer. My colleague is testing it now (I will leave for two weeks vacation) and will get back to you as soon as possible.There is on little doubt left. It kind of tells the right thing. It is showing "unknown" and the telc...

roland.bellwald · 04-23-2007

Hi Mehmet,Thanks a lot, this helped and it is working perfectly fine now :)Roland

roland.bellwald · 02-20-2007

The following link did help...http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_administration_guide_chapter09186a008065c43c.html#wp1107885Note:If you are using Cisco Unified CallManager 5.0 or later, verify that the AXL service is activ...

roland.bellwald · 07-20-2006

Dear Forum,Thanks for the answer so far, I did investigate a bit further and found out...As soon as username and password is entered in the user options, the "Cisco User Options" can be selected by rightclicking on the communicator.Further, it does t...

roland.bellwald · 06-22-2006

I did observe a similar behaviour. Having the same setup with CCM4.1(3), CVTA 2.0 or 7985 phones, the connection is audio only until I put the call on a CallManager device on hold an resume it. Then it works fine.Does someone know how to avoid this?C...

Member Since	‎06-25-2003 04:21 PM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	23
Total Helpful Votes Received	10

User Statistics

User Activity

Calling Party number not Displayed on 6941 SIP phone 9.2(1) firmware

IOS H.323 / H.320 Bonding with LifeSize Video Endpoint

HHC or Remote Hookswitch Control on CME

Configure H.323 and CCM Fallback (SRST) for Overlap Sending

CUE 2.3(2) Integration into CCM 5.0(4) - Web Login Failed

Calling Party number not Displayed on 6941 SIP phone 9.2(1) firm

Re: Configure H.323 and CCM Fallback (SRST) for Overlap Sending

Re: CUE 2.3(2) Integration into CCM 5.0(4) - Web Login Failed

Re: Where can the IP Communicator User Options be defined?

Re: VT Advantage 2.0(1)a and H.323 endpoints