About adrienbomble

adrienbomble · 01-15-2014

Hello Gents,We have an issue with a very basic GRE configuration ; GRE Tunnel is up/up on one side but up/down on the other side.It's possible to ping tunnel destination from each side, but the tunnel doesn't come up.Here are router configs :R1 (Cisc...

adrienbomble · 03-28-2012

Hello guys,I have an issue trying to configure NAT as described on the diagram below:- Host A must use IP 10.100.117.253 to communicate with Host B- Host B must use IP 172.16.3.10 to communicate with Host AI managed to translate source IP address (ip...

adrienbomble · 06-02-2009

Hello all,I am trying to create a netconfig job but i have an issue: I am not able to select devices in the device selector left window. I am seeing all my devices but the box i have to click to select the device appears in light grey and it's not cl...

adrienbomble · 04-15-2009

Hello,I have an issue with one kind of device: WS-C2950G-24-EI. This kind of device appears as "Unknow device". When i look in Common services, i have got a small question mark icon next to the device.Moreover, RME is not able to fetch the config.Cou...

adrienbomble · 03-03-2009

Hello All,We've just installed LMS 3.1 on Windows 2003 Server and i've got some issues...The 5 processes below are down (see screenshot attached LMS31_3.jpg):DFMCTMStartupCfmDbMonitorDFMOGSServerNOSServerPTM ServerAs a consequence, as you can see in ...

adrienbomble · 03-29-2012

Yes, i am sorry R2 and R1 router have been mismatched in my message;----------------------------------------------------------R2:interface FastEthernet0/0 ip address 10.100.117.254 255.255.255.0 ip nat inside duplex auto speed auto!interface FastEthe...

adrienbomble · 03-28-2012

Hello,Thanks for your reply. I have also labbed this... but using GNS3 and not real devices. Maybe the strange behaviour i have comes from GNS3 network simulator ? Then you're right about the host requirements i posted on my first message, there was ...

adrienbomble · 03-28-2012

Hello J.Blakley,Thanks for your answer. Yes, R3 knows how to get back to 10.100 subnet. I have defined static routes on all routers.

adrienbomble · 06-03-2009

Hello,You were right, i tried too early after restarted the server ; )Now everything is working fine, and i am now able to select the devices. The problem was really coming from the packages.Thanks again for your help,Best Regards,Adrien

adrienbomble · 06-03-2009

Hello,Thanks for your reply ! I tried what you advised, and i have now a new error when i am accessing netconfig:CFG0008: Error occured while processing.Possible Cause: URN_NOT_FOUND : urn "JRM" : Not found !!Now the two Netconfig windows (device sel...

Member Since	‎05-11-2007 12:07 AM
Date Last Visited	‎07-11-2018 12:38 AM
Posts	27

User Statistics

User Activity

GRE issue ; Tunnel up/down on one side and up/up on the other side

NAT; Unable to translate destination IP Address ?

Netconfig issue : Impossible to select devices when creating a job

LMS 3.1 Unknow device : WS-C2950G-24-EI

LMS 3.1 : Processes down for unknown reason...

NAT; Unable to translate destination IP Address ?

NAT; Unable to translate destination IP Address ?

NAT; Unable to translate destination IP Address ?

Re: Netconfig issue : Impossible to select devices when creating

Re: Netconfig issue : Impossible to select devices when creating