About r-barbosa

r-barbosa · 09-26-2018

Hi all. I got a switch 2940 and plugged in my 2950 switch but it did not link the port did not signal. I have never had problems with cisco switches, here are the firmware versions for each. And strange not to link to the port the strange thing is th...

r-barbosa · 08-17-2015

Ola pessoal Possuo um roteador 2800 com uma placa com 4FXS e 4 FXO o meu tronco chega na porta fxo e tenho 4 ramais na porta FXS quero ativar o recurso de transferencia de chamada(call transfer) utilizando o seguinte link http://www.cisco.com/c/en/us...

r-barbosa · 03-25-2015

Hi all, I have a router with CME and 4 FXS ports, would like to set up call transfer that is possible with analog phones and FXS port and CME? Regards

r-barbosa · 10-31-2014

Hi all, I trying settings the follow environment. Exists any tecnology permit the vlans the client 1 go encapsulation into vlan 100 and traffic client 2 into vlan200. I trying follow setting switchport mode dot1q-tunnel I reserarching the 802.1ad an...

r-barbosa · 05-11-2014

Hi all. I trying setting the environment with GEPON and CISCO C3750X, I have the follow topology. The equipment GEPON have interfaces OLT(optical Line Terminator) with port fiber and port gigaethernet. This port is connnected port switch 3750x, port...

r-barbosa · 09-30-2018

Thanks Leo. Its works. I put the cable cross and it worked perfectly. And what you said 2940 and 2950 do not support MDI / MDIX. I just had to set the duplex to full manual and it worked. Thank you very much Regards

r-barbosa · 09-27-2018

why are the two gigabitEthernet interface needs to cross? but I still tested with cross and it did not work. A friend told me that he already had a problem with distinct IOS versions that the encapsulation is not compatible, have you heard anything l...

r-barbosa · 09-27-2018

Hi follow output command2940# show interfaces gigabitEthernet 0/1 switchport Name: Gi0/1Switchport: EnabledAdministrative Mode: dynamic desirableOperational Mode: downAdministrative Trunking Encapsulation: dot1qNegotiation of Trunking: OnAccess Mode ...

r-barbosa · 08-28-2015

Hi all. I solved the problem, it was my fault. I had a "connection plar" to the actual number and used a dial-peer to direct for FXS, there have set up the "connection plar" straight to the extension and the transfer worked. I'm sorry. Thank you very...

r-barbosa · 08-28-2015

Pessoal resolvi cagada minha eu tinha um "connection plar" para o numero real e usava um dial-peer para jogar para a FXS, ai coloquei o connection plar direto para o ramal e a transferencia funcionou. resolveu me desculpem. Muito obrigado pela ajuda ...

Member Since	‎03-22-2008 10:47 AM
Date Last Visited	‎10-12-2018 12:22 AM
Posts	81
Total Helpful Votes Received	21

User Statistics

User Activity

Not Link port switch 2940 and 2950

Telefones analogicos em porta FXS com recurso transferencia de chamada ativado

CME with telephones analogic in port FXS

802.1ad vs qinq

QinQ with plataform GEPON

Re: Not Link port switch 2940 and 2950

Re: Not Link port switch 2940 and 2950

Re: Not Link port switch 2940 and 2950

Hi all. I solved the problem,

Pessoal resolvi cagada minha