Cisco Support
English
Feedback Help
Cisco Support Community
Register
cancel
turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
Member since ‎12-21-2010
‎07-04-2018
Georgios Fotiadis
Georgios Fotiadis
Gold

Re: Call Forward All not working for in...

Created by Georgios Fotiadis Gold in IP Telephony
‎05-04-2018 03:47 AM
‎05-04-2018 03:47 AM
Incoming calls land directly to operator's extension (or through an AA)? Which partition do operator and other extensions belong to? What is your "entry" to your CUCM; a SIP trunk? ... View more

Re: Call Forward All not working for in...

Created by Georgios Fotiadis Gold in IP Telephony
‎05-04-2018 03:30 AM
‎05-04-2018 03:30 AM
Check the CSS next to the Call Forward All Destination at DN configuration page. ... View more

Re: Phone can do only outbound call

Created by Georgios Fotiadis Gold in Other Collaboration, Voice, and Video Subjects
‎04-25-2018 11:35 PM
‎04-25-2018 11:35 PM
You can place the DN of the requested phone to a new (unused) partition. That way, no one will have access to the DN (since that partition will not be present in any Calling Search Space) and the user will be able to place outgoing calls, according to the phones CSS. ... View more

Re: CME Debugging

Created by Georgios Fotiadis Gold in IP Telephony
‎03-18-2018 04:56 AM
‎03-18-2018 04:56 AM
Issue "logging monitor" at global configuration mode. ... View more

Re: CME Debugging

Created by Georgios Fotiadis Gold in IP Telephony
‎03-18-2018 04:27 AM
‎03-18-2018 04:27 AM
If "term mon" is open, and you simply issue "conf t" and then "exit", do you see anything on the screen? How have you connected to the device? ... View more

Re: CME Debugging

Created by Georgios Fotiadis Gold in IP Telephony
‎03-18-2018 04:14 AM
‎03-18-2018 04:14 AM
If you have used telnet/ssh to login to the device, you need issue "terminal monitor" in privileged more; this command is not needed when you connect through console. Alternatively you can use "logging buffered" to write debug output to local buffer and later view it with "show logging". ... View more

Re: External Call Forwarding

Created by Georgios Fotiadis Gold in IP Telephony
‎03-13-2018 03:35 AM
‎03-13-2018 03:35 AM
Can you attach the output of debug ccsip messages and your running configuration? Also, when the call transfer is established, do you see packets increasing at show voip rtp connections detail for the corresponding call? Finally, what is the output of show call active voice brief? ... View more

Re: callback Softkey For 6921

Created by Georgios Fotiadis Gold in IP Telephony
‎03-13-2018 02:46 AM
‎03-13-2018 02:46 AM
Normally, adding the CallBack softkey in Ring Out state should have done the job for you. What is you dial out and the destination is On Hook? Do you get the CallBack softkey there? ... View more

Re: External Call Forwarding

Created by Georgios Fotiadis Gold in IP Telephony
‎03-13-2018 02:36 AM
‎03-13-2018 02:36 AM
How are you connected to the outside? Through a SIP trunk from CME to the ITSP? Can you dial from the inside to the outside successfully? Have you enabled SIP inspection on your ASA? ... View more

Re: forward incoming calls from sip tru...

Created by Georgios Fotiadis Gold in IP Telephony
‎03-11-2018 05:15 AM
‎03-11-2018 05:15 AM
Create a translation pattern at CUCM (Call Routing -> Translation Pattern). ... View more

Re: Cisco ip phone 9971 getting registr...

Created by Georgios Fotiadis Gold in IP Telephony
‎03-10-2018 06:20 AM
‎03-10-2018 06:20 AM
Delete the ITL files (under Security Configuration) on the IP Phone settings (directly on the IP Phone itself). ... View more

Re: what is the best and recommended/ea...

Created by Georgios Fotiadis Gold in IP Telephony
‎03-10-2018 06:19 AM
‎03-10-2018 06:19 AM
The best way would be to use the Bulk Admin Tool (BAT). You practically create an Excel document that contains the MAC/DNs etc, so as to massively create the configuration at CUCM for all 150 IP Phones. More info here: Cisco Unified Communications Manager Bulk Administration Guide ... View more

Re: CUCM -> Flowroute outbound calls wo...

Created by Georgios Fotiadis Gold in IP Telephony
‎03-09-2018 10:59 AM
‎03-09-2018 10:59 AM
This is a DTMF negotiation issue. What is the dtmf-relay configured under your dial-peers (incoming from eg. CUCM and outgoing to Flowroute)? ... View more

Re: IVR--ANALOG-PHONE

Created by Georgios Fotiadis Gold in IP Telephony
‎02-27-2018 10:55 PM
‎02-27-2018 10:55 PM
Of-course, if MGCP/SCCP integrated, they would be extensions belonging to the same cluster. If not (i.e. you have an H.323 trunk to the VG), you can always transfer from the IP phones to an "external" number (the analog phones). ... View more

Re: IVR--ANALOG-PHONE

Created by Georgios Fotiadis Gold in IP Telephony
‎02-27-2018 10:53 PM
‎02-27-2018 10:53 PM
You can create an IVR at CUC using Call Handlers. Also, you can insert you analog phones and extensions (the ones connected at the VG310) in CUCM using MGCP integration. ... View more
Public Statistics
Date Registered ‎12-21-2010 05:44 AM
Date Last Visited ‎07-04-2018 12:05 AM
Total Messages Posted 415
Total Helpful Votes Received 620
Badges
Helpful Votes From