Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco SX 20 Out going Call Dialing issue

 

Hello Team,

 

Hello Team,

We are using Cisco SX20 and configured the Public Ip address,

We can able receive the call from outside but not able call dial out,i have tried several Public IP address for the testing but none of them not working.

There is no gatekeeper ,Public Ip address configured directly to the system.

Please suggest the same 

 

Thanks in advance

 

 

1 ACCEPTED SOLUTION

Accepted Solutions

...and are you specifying

Are call set-up mode set to "Direct" and are you specifying call protocol as H.323 ?

/jens

Please rate replies and mark question(s) as "answered" if applicable.

Please rate replies and mark question(s) as "answered" if applicable.
7 REPLIES

Two things; ensure call

Two things; ensure call protocol is set to H.323, and are your system behind a firewall?

Make sure you test with an address which is known to be "good", such as the one found at http://vtctest.pointsofdata.com/

/jens

Please rate replies and mark question(s) as "answered".

Please rate replies and mark question(s) as "answered" if applicable.
New Member

Thanks for your replay We

Thanks for your replay

 

We have connected VC directly to the internet there is no Firwall in between.

Also have already tried the the above test IP address but call is not going.

Thanks

...and are you specifying

Are call set-up mode set to "Direct" and are you specifying call protocol as H.323 ?

/jens

Please rate replies and mark question(s) as "answered" if applicable.

Please rate replies and mark question(s) as "answered" if applicable.
New Member

Yes,I have trying h.323 calls

Yes,I have trying h.323 calls and tried use and Direct and gate keeper but no luck.

I have seen some other discussion also please find the below link

https://supportforums.cisco.com/discussion/12077571/sx20-system-not-registered-h323-protocol

https://supportforums.cisco.com/discussion/11687241/cisco-telepresence-isdn-link-sx20

i think need to upgrade the system software for the same please suggest the same.

Regards

Renji

Software ​version should not

Software ​version should not matter since you are dialling IP addresses and not a URI type address such as Alias@domain, which can only be done without being registered to a Gatekeeper as of TC4.2 and later. Having said that, what software version does it currently have?

Might be helpful if you could capture xconfiguration and xstatus output and upload/attach those files here.

/jens

Please rate replies and mark question(s) as "answered" if applicable.

Please rate replies and mark question(s) as "answered" if applicable.
New Member

Sorry Jen,Currently i am not

Sorry Jen,

Currently i am not in customer site,

I will keep you update..

 

Looks like there could be an

Looks like there could be an issue with the test addresses on http://vtctest.pointsofdata.com/ - however, 140.242.250.204 and 140.242.250.205 both works - these are Polycom hosted test facilities. Would be an idea to try either or both of those.

If you can't connect to those addresses, SSH into the system, use the following commands;

systemtools network ping 140.242.250.204

systemtools network traceroute 140.242.250.204

This should give you an idea where the call fails.

(You can also get xstatus and xconfiguration by loggin in remotely using SSH.smiley)

/jens

Please rate replies and mark question(s) as "answered" if applicable.

 

Please rate replies and mark question(s) as "answered" if applicable.
452
Views
0
Helpful
7
Replies
CreatePlease login to create content