Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

DTMF Relay doesnt appear to work CME to CUE

I am able to make calls in to my CUE but I cant enter my pin.  It acts like its not getting any button presses.  I assume there is something wrong with my DTMF relay.  Here is the sho run of the realavent parts:

 

voice service voip
 ip address trusted list
  ipv4 10.1.5.2 255.255.255.255
  ipv4 10.1.5.3 255.255.255.255
  ipv4 10.1.6.3 255.255.255.255
  ipv4 10.1.6.2 255.255.255.255
  ipv4 10.1.7.2 255.255.255.255
  ipv4 10.1.131.1 255.255.255.255
  ipv4 10.1.131.2 255.255.255.255
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 no supplementary-service sip handle-replaces
 fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
 sip
  bind control source-interface GigabitEthernet0/1
  bind media source-interface GigabitEthernet0/1
  registrar server

 

voice register global
 mode cme
 max-dn 4
 max-pool 4
 load 7961 SIP41.9-1-1SR1S.loads
 load 7941 SIP41.9-1-1SR1S.loads
 timezone 22
 voicemail 4500
 tftp-path flash:
 create profile sync 0011101915212849
!
voice register dn  1
 number 4001
 call-forward b2bua busy 4500
 call-forward b2bua noan 4500 timeout 10
 name Peter Brown
 label Peter Brown
 mwi

 

voice register pool  1
 id mac 001F.CA35.0A91
 type 7961
 number 1 dn 1
 codec g711ulaw

 

dial-peer voice 4500 voip
 destination-pattern 450[01]
 session protocol sipv2
 session target ipv4:10.1.130.2
 dtmf-relay sip-notify
 codec g711ulaw
 no vad

 

sip-ua
 mwi-server ipv4:10.1.130.2 expires 3600 port 5060 transport udp

 

interface Integrated-Service-Engine1/0
 ip unnumbered GigabitEthernet0/1
 service-module ip address 10.1.130.2 255.255.255.0
 !Application: CUE Running on NME
 service-module ip default-gateway 10.1.130.1
 no keepalive

 

 

 

 

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted

First, I would check your CUE

First, I would check your CUE configuration to verify the DTMF method you have provisioned there. Session to the NME and execute the command:

show ccn subsystem sip

Make sure the DTMF method reported by CUE matches the voip dial-peer you have pointing to CUE.

Next, I would also specify the same DTMF method under the "voice register pool 1" configuration stanza.

HTH.

-Bill (@ucguerrilla)

http://ucguerrilla.com

 

HTH -Bill (b) http://ucguerrilla.com (t) @ucguerrilla

Please remember to rate helpful responses and identify

2 REPLIES
Highlighted

First, I would check your CUE

First, I would check your CUE configuration to verify the DTMF method you have provisioned there. Session to the NME and execute the command:

show ccn subsystem sip

Make sure the DTMF method reported by CUE matches the voip dial-peer you have pointing to CUE.

Next, I would also specify the same DTMF method under the "voice register pool 1" configuration stanza.

HTH.

-Bill (@ucguerrilla)

http://ucguerrilla.com

 

HTH -Bill (b) http://ucguerrilla.com (t) @ucguerrilla

Please remember to rate helpful responses and identify

New Member

I ended up calling TAC.  The

I ended up calling TAC.  The fix ended up being setting everything to "rtp-ne". 

394
Views
0
Helpful
2
Replies
CreatePlease to create content