Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

2650XM dial-peer using Trunks

Hi,

I got a customer with a 2650XM IOS vers. 12.4(19b) (c2600-adventerprisek9_ivs-mz.124-19b), I cannot use ports only Trunks and I cannot get the dial-peers to work. I programmed the Controller with the PRI and D-channel with a Trunk label but not voice-port is created.

I had to replace his router with a temporary 2821 and everything is Ok but of course I need to recover the 2821, his router was working before with another solution, not Cisco, so they didn't want to buy a new one and a PRI card.

I am guessing I don't understand the whole TRUNK programming for Dial-Peers, any help will be appreciated, below are the pieces of config and debug relevant to this.

Regards,

Hiram

**********

CONFIG

trunk group PSTN

description PRI Line to PSTN

!

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

description PRI T1 for PSTN

!

interface Serial1/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-dms100

isdn incoming-voice voice

isdn supp-service name calling

trunk-group PSTN

no cdp enable

!

dial-peer voice 1 pots

incoming called-number .

trunk-group-label source PSTN

direct-inward-dial

!

dial-peer voice 201 pots

description Primary Outbound Dial Peer for 10 Digits - Local Services

preference 1

destination-pattern 8305[2-9]......

trunk-group-label target PSTN

prefix 305

!

dial-peer voice 1000 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

incoming called-number 8T

dtmf-relay h245-alphanumeric

!

dial-peer voice 1011 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

dtmf-relay h245-alphanumeric

!

**********

DEBUG

HQ1VGW1#

*Mar 2 07:57:46.828: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Calling Number=1000, Called Number=83059998002, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*Mar 2 07:57:46.828: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1000

*Mar 2 07:57:46.832: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Calling Number=1000, Called Number=83059998002, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*Mar 2 07:57:46.832: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1000

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersCore:

Calling Number=, Called Number=83059998002, Peer Info Type=DIALPEER_INFO_SPEECH

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=83059998002

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersCore:

No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersMoreArg:

Result=NO_MATCH(-1)

HQ1VGW1#

  • Voice over IP
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: 2650XM dial-peer using Trunks

Under DP, it's "trunkgroup".

Note, yout DP 1 doesn't need or use it.

Note if you have no voice-port, likely you're not using the right hardware or do not have enough dsp. Check "show diag" about that

5 REPLIES
Hall of Fame Super Gold

Re: 2650XM dial-peer using Trunks

Under DP, it's "trunkgroup".

Note, yout DP 1 doesn't need or use it.

Note if you have no voice-port, likely you're not using the right hardware or do not have enough dsp. Check "show diag" about that

New Member

Re: 2650XM dial-peer using Trunks

Thanks for responding.

HQ1VGW1#sh diag

Slot 0:

C2650XM 1FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time 17:09:56 ago

EEPROM contents at hardware discovery:

Hardware Revision : 3.0

PCB Serial Number : FFFF

Part Number : 73-7755-04

RMA History : 00

RMA Number : 0-0-0-0

Board Revision : A0

Deviation Number : 0-0

Product (FRU) Number : C2650XM-1FE

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 6E 41 03 00 C1 0B FF FF FF 46 46 46

0x10: 46 FF FF FF FF 82 49 1E 4B 04 04 00 81 00 00 00

0x20: 00 42 41 30 80 00 00 00 00 FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

FT1 BT8360

Hardware revision 1.3 Board revision E0

Serial number 25639147 Part number 800-03279-04

FRU Part Number WIC-1DSU-T1=

Test history 0x0 RMA number 00-00-00

Connector type Wan Module

EEPROM format version 2

EEPROM contents (hex):

0x20: 02 11 01 03 01 87 38 EB 50 0C CF 04 00 00 00 00

0x30: 70 00 00 00 02 08 27 01 FF FF FF FF FF FF FF FF

Slot 1:

CT1 (CSU) Port adapter, 1 port

Port adapter is analyzed

Port adapter insertion time 17:09:55 ago

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision B0

Serial number 29805542 Part number 800-01228-05

FRU Part Number NM-1CT1-CSU=

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x00: 01 26 01 01 01 C6 CB E6 50 04 CC 05 00 00 00 00

0x10: 58 00 00 00 04 05 08 00 FF FF FF FF FF FF FF FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF

HQ1VGW1#

HQ1VGW1#sh isdn status

Global ISDN Switchtype = primary-dms100

ISDN Serial1/0:23 interface

dsl 0, interface ISDN Switchtype = primary-dms100

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x807FFFFF

Number of L2 Discards = 0, L2 Session ID = 2

Total Allocated ISDN CCBs = 0

HQ1VGW1#

Regards,

Hiram

New Member

Re: 2650XM dial-peer using Trunks

I made those changes (trunkgroup, DP1) and the dial peers are matching but still not working, please check "ccapi inout".

Thanks is advanced.

*********

New dial-peer

dial-peer voice 1 pots

incoming called-number .

direct-inward-dial

!

dial-peer voice 201 pots

trunkgroup PSTN

description Primary Outbound Dial Peer for 10 Digits - Local Services

preference 1

destination-pattern 8305[2-9]......

prefix 305

!

dial-peer voice 1000 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

incoming called-number 8T

dtmf-relay h245-alphanumeric

!

dial-peer voice 1011 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

dtmf-relay h245-alphanumeric

!

New Member

Re: 2650XM dial-peer using Trunks

Thanks Dear Bevilacqua,

The issue with the dial-peers using trunk was resolved, now that I passed that step, I have another issue in my next step, the connection to the PSTN(T1/PRI), I will open a different post for that.

Thanks again.

Hall of Fame Super Gold

Re: 2650XM dial-peer using Trunks

You cannot use this router for voice, it has no voice card.

The NM-1CT1 is only for data and modem, not voice.

You need NM-HDV-xxx for voice.

375
Views
0
Helpful
5
Replies
This widget could not be displayed.