Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

adding new E1 to NAS & PGW problem ?????? .................................

Dears all,

itried to add new E1 to my system but ss7 signal didn't come up, i attached my test commands and my PGW and NAS configurations, just i need to mention that now i have 2 E1s are running with no probles but when i add new E1 the problems appeared ..... any help please ?

---------------------------------

NAS configuration:

controller E1 7/7

framing NO-CRC4

channel-group 0 timeslots 1

pri-group timeslots 2-31 nfas_d primary nfas_int 0 nfas_group 2

description Connection to International

!

interface Serial7/7:0

no ip address

encapsulation ss7

channel-id 2

!

interface Serial7/7:15

no ip address

encapsulation hdlc

isdn switch-type primary-ni2c

isdn incoming-voice modem

isdn map address . plan isdn type network

isdn rlm-group 2

no isdn send-status-enquiry

isdn negotiate-bchan resend-setup

isdn bchan-number-order ascending

no cdp enable

rlm group 2

protocol rlm port 3004

server PGW1

link address 55.55.55.50 source FastEthernet0/0 weight 1

ss7 session 0 address 55.55.55.50 7000 55.55.55.49 7000 session-set 0

ss7 mtp2-variant Bellcore 3

ss7 mtp2-variant itu 0

SUERM-number-octets 16

================================================

PGW configuration:

prov-add:DPC:NAME="dpc-inter",DESC="DPC of inter",NETADDR="1.1.2",NETIND=3

prov-add:SS7PATH:NAME="ss7p-jtc-inter",DESC="ss7 path to inter",MDO="ETS_300_356",CUSTGRPID="0000",SIDE="network",DPC="dpc-inter",OPC="tar-opc",M3UAKEY="",ORIGLABEL="",TERMLABEL=""

prov-add:LNKSET:NAME="linkset-inter",DESC="Link Set inter",APC="dpc-inter",PROTO="SS7-ITU",TYPE="IP"

prov-add:SS7ROUTE:NAME="ss7route-inter",DESC="ss7 route to inter",OPC="tar-opc",DPC="dpc-inter",LNKSET="linkset-inter",PRI=1

prov-add:NASPATH:NAME="naspath3-inter",DESC="Nas Path to AS5400 to inter",EXTNODE="as5400",MDO="BELL_1268_C2",CUSTGRPID="0000",SIGSLOT=0,SIGPORT=0

prov-add:C7IPLNK:NAME="cs7iplinktointer",DESC="cs7 link to inter",LNKSET="linkset-inter",SLC=0,PRI=1,TIMESLOT=2,SESSIONSET="cs7set1"

prov-add:IPLNK:NAME="nas-iplink3",DESC="IP link 3 to AS5400",SVC="naspath3-inter",IPADDR="IP_Addr1",PORT=3005,PEERADDR="55.55.55.49",PEERPORT=3005,PRI=1,IPROUTE=""

prov-add:nailedtrnk:name="4002",srcsvc="ss7p-jtc-inter",dstsvc="naspath3-inter",srcspan="ffff",dstspan="1",srctimeslot="2",dsttimeslot="1",spansize=30

thank you for any helping

BR,

166
Views
0
Helpful
0
Replies
CreatePlease login to create content