Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

AS5350 “Call not end-to-end ISDN, may have in-band info”

Hi All,

Nov 12 05:20:13.687: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0F6C

Bearer Capability i = 0x9090A2

Standard = CCITT

Transer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Progress Ind i = 0x8081 - Call not end-to-end ISDN, may have in-band info

Calling Party Number i = 0x2181, '12135932700'

Plan:ISDN, Type:National

Called Party Number i = 0x80, '2709'

Plan:Unknown, Type:Unknown

Nov 12 05:20:13.695: ISDN Se2/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8F6C

Channel ID i = 0xA98381

Exclusive, Channel 1

Nov 12 05:20:13.987: ISDN Se2/0:23 Q931: TX -> CONNECT pd = 8 callref = 0x8F6C

Nov 12 05:20:14.031: ISDN Se2/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x0F6C

Nov 12 05:20:31.583: ISDN Se3/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x0005

Cause i = 0x8090 - Normal call clearing

Nov 12 05:20:31.627: ISDN Se3/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x8005

Nov 12 05:20:31.631: ISDN Se3/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0005

Nov 12 05:20:32.731: ISDN Se2/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x0F6C

Cause i = 0x8290 - Normal call clearing

Nov 12 05:20:32.735: ISDN Se2/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x8F6C

Nov 12 05:20:32.779: ISDN Se2/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0F6C

Pls support in this

Thanks

  • Voice over IP
2 REPLIES
Cisco Employee

Re: AS5350 “Call not end-to-end ISDN, may have in-band info”

The bearer cap in the setup message translates to this:

Information Transfer Capability:

3.1 KHz Audio

Transfer Mode:

Circuit Mode

Information Transfer Rate:

64 Kbps

User Information Layer 1 Protocol:

G.711 u-Law Speech

So the call is looking to setup a 64k circuit, we actually make it all the way to connect so the setup is working, something else is telling isdn to tear down the call. Try some other debugs such as debug voip vspt err and debug voip ccapi err to see what may be happening, also look at show call hoist voice.

Hope this helps,

Chester

New Member

Re: AS5350 “Call not end-to-end ISDN, may have in-band info”

what exactly is the problem ?

Here you posted a debug which is showing normal call clearing.

This lines are not from this call's debug:

Nov 12 05:20:31.583: ISDN Se3/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x0005

Cause i = 0x8090 - Normal call clearing

Nov 12 05:20:31.627: ISDN Se3/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x8005

Nov 12 05:20:31.631: ISDN Se3/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0005

The Called Party Number is 2709 - is this correct ?

Robert

1396
Views
0
Helpful
2
Replies
This widget could not be displayed.