Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

AS5400 and SIP/H323 Voice calls..............??????????????................

Dears,

Que(1):what signal is output from AS5400.

Does it SIP or H323?

Que(2):i need to generate SIP and H323 Voice calls from AS5400 , can i do that?

if no what are your recommendations for AS5400 to be apple generate SIP and H323 Voice calls for other VoIP carriers?

Que(3): can AS5400 generate voice calls directly to other Carriers as:

AS5400 (calls SIP & H323)------to----- B carries.

any help please.

8 REPLIES
Hall of Fame Super Gold

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

1. Both. It is configured as "session protocol" under voip DP.

2. Yes

3. Yes

Hope this helps, please rate post if it does!

Community Member

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

Ok man thanks a lot.

i have this issue now:

Dear,

I tried to add new E1 to existed E1s. old E1 has slot time signalling with trunknailed called 1002, I need this New E1 without time signal mean to add to previous trunk 1002.

I added this command:

prov-add:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31

but when I added this new E1 to old E1,old E1 can not send or receive any calls (it is down) beside that new E1 doesn't run, I tried delete it using :

prov-dlt:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31

I added at AS5400 this commands:

controller E1 7/2

framing NO-CRC4

pri-group timeslots 1-31 nfas_d primary nfas_int 1 nfas_group 1

i delete every thing i put at PGW and AS5400.... but old E1 doesn't come up.

i need to say before adding new E1 every thing is will but after problems appeared, i have 2 E1s were running well now just one live and the other died.

i did blk and unblk at PGW but no changes at channel they still block.

i attached files for more details.

thanks for any help.

Hall of Fame Super Gold

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

Sorry, I can't help with SS7.

Community Member

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

thank you

Community Member

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

Sir,

to assist you, please send PGW configurations and your objetive: What E1s will be active in AS5400 and what are the SS7 configurations expected to work in this E1: CICs, signaling link been used.

to export PGW configuration, at the MML session, type:

prov-exp:all:dirname="20080815"

where is the name of the directory where the configurations will be saved.

this directory is created under

/opt/CiscoMGC/etc/cust_specific.

the files that interest in this case is the config.mml and the export_trunk.dat.

regards,

Daniel

Community Member

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

can please advise me with commands i should use to set AS5400 to originate and terminate voice calls in both SIP and H323?

Community Member

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

dears

can you please help if i can use MGCP with AS5400XM or not ???

Community Member

Re: AS5400 and SIP/H323 Voice calls..............??????????????.

Trying to answer your concerns:

1 - yes, it can do h.323, sip and mgcp. you can verify in this link:

http://www.cisco.com/en/US/prod/collateral/iad/ps505/ps6269/product_data_sheet0900aecd802efc92.html

2 - yes, you can.

3 - yes, just be carefull with security.

299
Views
0
Helpful
8
Replies
CreatePlease to create content