Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

ATA 187 and FAX

Hello,

I have problems with my ATA box 187.

it is plugged into my version of CUCM 8.0.3.20000-2

I declared a new device (Cisco ATA187) which I connected an analog phone. Until then, no problem. I can emit and receive calls from inside and outside.

I now wish to fax in place of my analog phone and there problem: nothing works, I see the start of communication between two fax but no data.

I tried Fax passtrought and T.38 Fax passtrought

here is a

term mon  / debug isdn q931 show :

May 28 09:11:52.005: ISDN Se0/1/1:15 Q931: TX -> SETUP pd = 8  callref = 0x00CD

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '491563695'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '0491562008'

                Plan:Unknown, Type:Unknown

May 28 09:11:52.109: ISDN Se0/1/1:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x80CD

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

May 28 09:11:53.013: ISDN Se0/1/1:15 Q931: RX <- PROGRESS pd = 8  callref = 0x80CD

        Cause i = 0x87F2 - Unknown cause value

        Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band info

May 28 09:11:53.013: ISDN Se0/1/1:15 Q931: RX <- ALERTING pd = 8  callref = 0x80CD

May 28 09:12:15.459: ISDN Se0/1/1:15 Q931: RX <- CONNECT pd = 8  callref = 0x80CD

May 28 09:12:15.463: ISDN Se0/1/1:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x00CD

May 28 09:12:52.875: ISDN Se0/1/1:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x00CD

        Cause i = 0x8090 - Normal call clearing

May 28 09:12:53.159: ISDN Se0/1/1:15 Q931: RX <- RELEASE pd = 8  callref = 0x80CD

May 28 09:12:53.179: ISDN Se0/1/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x00CD

what other actions should I take?

Sincerely,

Everyone's tags (4)
1 REPLY
New Member

ATA 187 and FAX

i add my CUCM conf

!

ccm-manager fallback-mgcp

ccm-manager redundant-host 192.168.xxxx

ccm-manager mgcp

no ccm-manager fax protocol cisco

ccm-manager music-on-hold

ccm-manager config server 192.168.xxxx 192.168.xxxx

ccm-manager config

!

mgcp

mgcp call-agent 192.168.xxxx 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp modem passthrough voip codec g711alaw

no mgcp package-capability res-package

no mgcp timer receive-rtcp

mgcp fax rate 14400

mgcp fax t38 ecm

mgcp fax t38 inhibit

mgcp bind control source-interface GigabitEthernet0/0

mgcp bind media source-interface GigabitEthernet0/0

!

mgcp profile default

!

890
Views
0
Helpful
1
Replies