Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Auto QoS on a 2800 Series Router

Hello

I want activate Auto QoS on a Cisco 2800 Series Router.

If I change in the Giga-Interface config mode and type "auto qos" than I get the information, that this command does't exist.

What's wrong there. Is there no auto qos on this router?

Yours sincerely

9 REPLIES
Community Member

Re: Auto QoS on a 2800 Series Router

Hi,

AutoQos is only available on

- ATM PVCs (high and low subinterfaces only)

- Frame Relay DLCIs (point to point Only)

- Serial interface using PPP or HDLC

Bear in mind there are additional prerequisite config requrements for AutoQos.

It would be a good idea check the feature navigator to see if your IOS supports AutoQos Enterprise (12.3T onwards)

Hope this helps.

Regards,

Dave Tucker

Community Member

Re: Auto QoS on a 2800 Series Router

I have a 2801 and loaded FW ver 12.4(16a) on it and was able to apply AutoQOS on on the FE interface.

Although I haven't tested it yet since my counterpart on the far-end is still setting-up.

Do you this Auto-QOS will not work on the FE port?

Thanks,

Robert

Community Member

Re: Auto QoS on a 2800 Series Router

I have only Gigabit-Interfaces.

This is the output of the show version. Maybe this will help?

R2#sh version

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(6)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Wed 22-Feb-06 22:54 by ccai

ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)

R2 uptime is 15 minutes

System returned to ROM by reload at 12:11:10 UTC Wed Dec 19 2007

System image file is "flash:c2800nm-advipservicesk9-mz.124-6.T.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2821 (revision 53.51) with 237568K/24576K bytes of memory.

Processor board ID FHK0841F0VU

2 Gigabit Ethernet interfaces

2 Low-speed serial(sync/async) interfaces

1 ISDN Basic Rate interface

1 ATM interface

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

125184K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Community Member

Re: Auto QoS on a 2800 Series Router

I don't know if this will help but I am running policy map with class maps applied to the gig interface using service policy command? Is this for voice

Community Member

Re: Auto QoS on a 2800 Series Router

It's for voice and for other applications.

I can also run QoS with class maps and policy maps. But I would test QoS.

Community Member

Re: Auto QoS on a 2800 Series Router

Does nobody has an idea? What could be the problem?

Best regards

VIP Purple

Re: Auto QoS on a 2800 Series Router

Can you post the exact commands you are entering from the time you login to the router up to and including the error message you receive?

Brandon

Community Member

Re: Auto QoS on a 2800 Series Router

Hello

I do "configure terminal".

Then I do "interface gigabitEthernet 0/0"

And then I will put the command "auto qos".

But there ist no command "auto"

Do I make something wrong?

Best regards

VIP Purple

Re: Auto QoS on a 2800 Series Router

As mentioned in a previous post, auto qos is not available on GigE interfaces on a router. See the following link.

http://www.cisco.com/en/US/technologies/tk543/tk879/technologies_qas0900aecd8020a589_ps6613_Products_Q_and_A_Item.html

Brandon

5423
Views
0
Helpful
9
Replies
CreatePlease to create content