06-12-2008 11:10 AM
Dear how i can change username and password for PGW2200?
can give the procedures?
thanks,
Solved! Go to Solution.
06-12-2008 02:00 PM
You can change user parameters using usermod command in solaris. You can remove or add usernames using the useradd or userdel commands in solaris.
You can change a users passwd using solaris command:
passwd
Do not remove mgcusr username from the box. It is ok to change its password. For example, to change the mgcusr password:
passwd mgcusr
Enter existing login password:
06-12-2008 02:00 PM
You can change user parameters using usermod command in solaris. You can remove or add usernames using the useradd or userdel commands in solaris.
You can change a users passwd using solaris command:
passwd
Do not remove mgcusr username from the box. It is ok to change its password. For example, to change the mgcusr password:
passwd mgcusr
Enter existing login password:
06-15-2008 02:07 AM
to be understood.... for example, if i have:
username:mgcusr
password:pgw321
can i change both username and password?
or just only password? .... i am interested with both to change.
username=mgcusr is built in system OS or i can delet it?
thank you
06-16-2008 09:55 AM
Don't change the login user for mgcusr. Only change the password.
06-17-2008 01:08 AM
ok i did.
can please advise me for my other issue for SS7 signaling to add new E1.
06-21-2009 09:00 PM
Still we can add another user with full or minimal MML privileges...at least 9.7(3) Installation and configuration guide discusses how to do so.
06-15-2008 03:39 AM
it is ok ....
thank you....
---------------
i have now this issue:
i need to add new E1 to be in the same trunk for previous E1 which is for Abdali. new E1 will not have signal it depeneds at old one timeslot.
i used this for new E1:
prov-add:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31
for old one this:
prov-add:nailedtrnk:name="1002",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="2",dsttimeslot="2",spansize=30
============================
at AS5400 i used to add new E1:
controller E1 7/2
framing NO-CRC4
pri-group timeslots 1-31 nfas_d primary nfas_int 1 nfas_group 0
Is this true or there are other commands i should use?
----------------------------
OLD E1 is configured as:
controller E1 7/0
framing NO-CRC4
channel-group 0 timeslots 1
pri-group timeslots 2-31 nfas_d primary nfas_int 0 nfas_group 0
description Connection to Abdali
interface Serial7/0:0
no ip address
encapsulation ss7
channel-id 0
!
interface Serial7/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-ni2c
isdn incoming-voice modem
isdn map address . plan isdn type network
isdn rlm-group 0
no isdn send-status-enquiry
isdn negotiate-bchan resend-setup
isdn bchan-number-order ascending
no cdp enable
any help please for correct commands i shall use? please see attached file for details.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: