Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

change username and password for PGW2200 ..... ????????....................

Dear how i can change username and password for PGW2200?

can give the procedures?

thanks,

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: change username and password for PGW2200 ..... ????????.....

You can change user parameters using usermod command in solaris. You can remove or add usernames using the useradd or userdel commands in solaris.

You can change a users passwd using solaris command:

passwd

Do not remove mgcusr username from the box. It is ok to change its password. For example, to change the mgcusr password:

passwd mgcusr

Enter existing login password:

6 REPLIES
Cisco Employee

Re: change username and password for PGW2200 ..... ????????.....

You can change user parameters using usermod command in solaris. You can remove or add usernames using the useradd or userdel commands in solaris.

You can change a users passwd using solaris command:

passwd

Do not remove mgcusr username from the box. It is ok to change its password. For example, to change the mgcusr password:

passwd mgcusr

Enter existing login password:

Community Member

Re: change username and password for PGW2200 ..... ????????.....

to be understood.... for example, if i have:

username:mgcusr

password:pgw321

can i change both username and password?

or just only password? .... i am interested with both to change.

username=mgcusr is built in system OS or i can delet it?

thank you

Cisco Employee

Re: change username and password for PGW2200 ..... ????????.....

Don't change the login user for mgcusr. Only change the password.

Community Member

Re: change username and password for PGW2200 ..... ????????.....

ok i did.

can please advise me for my other issue for SS7 signaling to add new E1.

Community Member

Re: change username and password for PGW2200 ..... ????????.....

Still we can add another user with full or minimal MML privileges...at least 9.7(3) Installation and configuration guide discusses how to do so.

Community Member

Re: change username and password for PGW2200 ..... ????????.....

it is ok ....

thank you....

---------------

i have now this issue:

i need to add new E1 to be in the same trunk for previous E1 which is for Abdali. new E1 will not have signal it depeneds at old one timeslot.

i used this for new E1:

prov-add:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31

for old one this:

prov-add:nailedtrnk:name="1002",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="2",dsttimeslot="2",spansize=30

============================

at AS5400 i used to add new E1:

controller E1 7/2

framing NO-CRC4

pri-group timeslots 1-31 nfas_d primary nfas_int 1 nfas_group 0

Is this true or there are other commands i should use?

----------------------------

OLD E1 is configured as:

controller E1 7/0

framing NO-CRC4

channel-group 0 timeslots 1

pri-group timeslots 2-31 nfas_d primary nfas_int 0 nfas_group 0

description Connection to Abdali

interface Serial7/0:0

no ip address

encapsulation ss7

channel-id 0

!

interface Serial7/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-ni2c

isdn incoming-voice modem

isdn map address . plan isdn type network

isdn rlm-group 0

no isdn send-status-enquiry

isdn negotiate-bchan resend-setup

isdn bchan-number-order ascending

no cdp enable

any help please for correct commands i shall use? please see attached file for details.

621
Views
0
Helpful
6
Replies
CreatePlease to create content