Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Code type is diaplayed "none" on gateway C2851

Hello.

There ar something wrong the status of the codec type.

The follow channel still seize line, even though user already disconnected call.

1/0/1:15.25, 1/0/1:15.27, 1/0/1:15.31

any good idea to reslove this issue?

regard,

John.

gateway#sh voi call sum

PORT CODEC VAD VTSP STATE VPM STATE

============== ======== === ==================== ======================

1/0/0:15.1 - - -

1/0/0:15.2 - - -

1/0/0:15.3 - - -

1/0/0:15.4 - - -

1/0/0:15.5 - - -

1/0/0:15.6 - - -

1/0/0:15.7 - - -

1/0/0:15.8 - - -

1/0/0:15.9 - - -

1/0/0:15.10 - - -

1/0/0:15.11 - - -

1/0/0:15.12 - - -

1/0/0:15.13 - - -

1/0/0:15.14 - - -

1/0/0:15.15 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/0:15.17 - - -

1/0/0:15.18 - - -

1/0/0:15.19 - - -

1/0/0:15.20 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/0:15.21 - - -

1/0/0:15.22 - - -

1/0/0:15.23 - - -

1/0/0:15.24 - - -

1/0/0:15.25 - - -

1/0/0:15.26 - - -

1/0/0:15.27 - - -

1/0/0:15.28 g711ulaw y S_CONNECT S_TSP_CONNECT

1/0/0:15.29 g711ulaw y S_CONNECT S_TSP_CONNECT

1/0/0:15.30 g711ulaw y S_CONNECT S_TSP_CONNECT

1/0/0:15.31 - - -

1/0/1:15.1 - - -

1/0/1:15.2 - - -

1/0/1:15.3 - - -

1/0/1:15.4 - - -

1/0/1:15.5 - - -

1/0/1:15.6 - - -

1/0/1:15.7 - - -

1/0/1:15.8 - - -

1/0/1:15.9 - - -

1/0/1:15.10 - - -

1/0/1:15.11 - - -

1/0/1:15.12 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/1:15.13 - - -

1/0/1:15.14 - - -

1/0/1:15.15 - - -

1/0/1:15.17 - - -

1/0/1:15.18 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/1:15.19 - - -

1/0/1:15.20 - - -

1/0/1:15.21 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/1:15.22 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/1:15.23 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/1:15.24 - - -

1/0/1:15.25 None - S_WAIT_RELEASE S_TSP_WAIT_RELEASE_COMPL

1/0/1:15.26 g711ulaw n S_CONNECT S_TSP_CONNECT

1/0/1:15.27 None - S_SETUP_FAIL S_TSP_WAIT_RELEASE_COMPL

1/0/1:15.28 - - -

1/0/1:15.29 g711ulaw y S_CONNECT S_TSP_CONNECT

1/0/1:15.30 - - -

1/0/1:15.31 None - S_SETUP_FAIL S_TSP_WAIT_RELEASE_COMPL

2 REPLIES
New Member

Re: Code type is diaplayed "none" on gateway C2851

Is the T1 configured for CAS fxo loop start.?? If yes then its a fxo disconnect issue. You configure timeout values under the voice port.

Regards

Venky

New Member

Re: Code type is diaplayed "none" on gateway C2851

Hello.

Gateway was configured with ISDN PRI E1 trunk.

can i still use the timeout value under voice port?

regards,

john.

196
Views
0
Helpful
2
Replies
CreatePlease login to create content