Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

dial peer config

Hi,

I config the three dial peers, the setting is following. I would like to achieve following:

1. the voice traffic sends to 192.168.16.1 and 192.168.16.2 as round robin mode (first call to 16.1, second call to 16.2, third call to 16.3, 4th 16.2, .... etc)

2. if both dial peer meet the max-con, it routes to 3rd dial peer.

however, the max-con of two dial peers are different (168 and 96). any work around of it?

It has timer to control the call route to another dial peer when it meets the max-con. how to config the timer?

If I config 10 dial peers. does the call always goes to the 1st dial peer first. If full, it goes second dial peer. If full, it goes 3rd dial peer. ..... etc

If so, does the call timeout when it try 10 dial peer?

! R1

dial-peer voice 88601 voip

tone ringback alert-no-PI

destination-pattern 886T

max-con 168

voice-class h323 1

session target ipv4:192.168.16.1

dtmf-relay rtp-nte digit-drop h245-signal h245-alphanumeric

fax-relay ecm disable

fax rate 9600

!

dial-peer voice 88602 voip

tone ringback alert-no-PI

destination-pattern 886T

max-con 96

voice-class h323 1

session target ipv4:192.168.16.2

dtmf-relay rtp-nte digit-drop h245-signal h245-alphanumeric

fax-relay ecm disable

fax rate 9600

!

dial-peer voice 88603 voip

tone ringback alert-no-PI

destination-pattern 886T

pref 1

max-con 125

voice-class h323 1

session target ipv4:172.16.1.1

dtmf-relay rtp-nte digit-drop h245-signal h245-alphanumeric

fax-relay ecm disable

fax rate 9600

!

rgds

5 REPLIES
Hall of Fame Super Gold

Re: dial peer config

Hi,

your config looks ok and should do what you described.

I did not understand your timeout question, can you rephrase it.

New Member

Re: dial peer config

Hi,

regarding the timeout issue

I config 10 dial peers (88601 - 88610) and the pref is 1 to 10.

dial peer voice 88601 voip

pref 1

dial peer voice 88602 voip

pref 2

dial peer voice 88603 voip

pref 3

:

:

1. does each call always try the 1st dial peer? if fails, it tries second dial peer. If fails, it tries third dial peer. .....

is it correct?

2. If I have 10 dial peer, does the call time out if it goes from 1st dial peer to 9 dial peer?

3. if two dial peers' max-con are different

e.g.

dial peer voice 88601

max-con 100

dial peer voice 88602

max-con 75

dial peer voice 88603

max-con 120

pref 1

does the 76th call go to 88603 (but there is 25 cct in 88601)?

Rgds

Hall of Fame Super Gold

Re: dial peer config

1. yes

2. the timer is reset for each hunt step across DPs. see: http://cisco.com/en/US/docs/ios/12_1t/12_1t2/feature/guide/dtcfgtim.html

3. per configuration given, the 76th calls goes via 88602. At that point, both DP 88601 and 88602 should have 38 calls each, and max-conn has not been reached yet.

As an appreciation for those proving answers, please rate useful posts with the scrollbox below!

New Member

Re: dial peer config

Hi,

regarding Q3, the 152 nd call, does it go "88603 dial peer"?

rgds

Hall of Fame Super Gold

Re: dial peer config

No, it goes via 88601, that at that point has 77 calls, hence has not reached the max-conn of 100.

I've notice that you have not reates posts yet, would you consider doing that to show your appreciation to those provide answers ?

192
Views
5
Helpful
5
Replies
CreatePlease to create content