cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
586
Views
0
Helpful
7
Replies

E1

worldcalltel
Level 1
Level 1

Objective: Configure the E1 with the following framing and line coding. Check the status of each port.

Req'd:

Framing: NO-CRC

Line Coding: CAS / HDB3

Config:

Router(config)#controllers e1 1/0

Router(config-controller)#no framing crc4

Router(config-controller)#linecode hdb3

Router(config-controller)#clock source line primary

Router(config-controller)#cas-group 1 timeslots 1-31 type r2-digital r2-compelled ani

Router(config-controller)#cas-custom 1

I'm using 3745 Cisco Router and setting up a 4 E1 ports to be open. My provider gave me the specs above, to configure. After i done this. We run some test, unfortunately the test was a failure. When issue the command show controller E1, the ports were down. I also check the voiceport, show voice port, the in and out status were idle and operation is down. My question is how do i resolve this problem? what possibly cause this? is there anything wrong with my config?

Thnks.Kindly notify me as soon as possible

7 Replies 7

amit.pandit
Level 1
Level 1

What exactly are you getting when you do

sh controller e1 ??

Could you upload the e1 config? (Use sh run and copy from there)

-AP

E1 1/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20040408, FPGA: 11, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 0.

Data in current interval (682 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

657 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

657 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 81 15 minute intervals):

0 Line Code Violations, 2 Path Code Violations,

70005 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

70006 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

---------------------------------------------

The ports was up now. follow up question.

When i test the call, everytime i monitor the calls, it shows "no circuit available". i try using the debug commands but no logs were displayed. what is wrong with this?i can't figure it out (it is obvious that my port were up, how come i got an error message no ciruit?). the provider said that the trunks were already open. but i can't make a call.

Hi,

to answer your questions without the relevant parts of your config is impossible. So can you please post your E1 controller config and the voice config (cut out security related things like passwords and the like).

Regards, Martin

GlobalTelwise3745#sho run

Building configuration...

Current configuration : 3057 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname GlobalTelwise3745

!

boot-start-marker

boot-end-marker

!

enable secret xxxx

!

username NOC password xxx

network-clock-participate slot 1

network-clock-participate slot 3

voice-card 1

dspfarm

!

voice-card 3

dspfarm

!

no aaa new-model

ip subnet-zero

!

!

ip cef

!

!

!

!

voice class codec 1

codec preference 1 g729br8

codec preference 2 g729r8

codec preference 3 g723ar63

codec preference 4 g723r63

codec preference 5 g723ar53

codec preference 6 g723r53

!

!

!

!

!

!

!

!

!

!

!

controller E1 1/0

framing NO-CRC4

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled

cas-custom 1

!

controller E1 1/1

framing NO-CRC4

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled

cas-custom 1

!

controller E1 3/0

framing NO-CRC4

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled

cas-custom 1

!

controller E1 3/1

framing NO-CRC4

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled

cas-custom 1

!

!

!

interface FastEthernet0/0

description Connection to LAN

ip address 210.x.77.x.255.255.252

duplex auto

speed auto

h323-gateway voip interface

h323-gateway voip id vm20 ipaddr 62.192.173.60 1718

h323-gateway voip h323-id TelwisePLDT

!

interface FastEthernet0/1

no ip address

duplex auto

speed auto

!

ip default-gateway 210.5.77.10

ip http server

ip classless

ip route 0.0.0.0 0.0.0.0 210.5.77.17

!

!

!

!

!

!

voice-port 1/0:1

input gain 6

echo-cancel coverage 32

bearer-cap Speech

!

voice-port 1/1:1

input gain 6

echo-cancel coverage 32

bearer-cap Speech

!

voice-port 3/0:1

!

voice-port 3/1:1

!

!

!

!

!

dial-peer voice 100 pots

description testing

destination-pattern 2503T

port 1/1:1

prefix 632

!

banner motd ^C

Warning!Authorized users only. ^C

alias exec active sh call act voi br

alias exec u undebug all

alias exec act sh call act voi br

alias exec sum sh voi port sum

alias exec ip sh call act voi br | include ip

alias exec histip sh call hist voi br | include ip

alias exec calls sh call res voi st

alias exec hist sh call hist voi br 5

alias exec scb show call active voice brief

alias exec sc show call active voice

alias exec sch show call history voice brief

alias exec sd show dial-peer voice sum

alias exec sv show voice port summary

alias exec ro show rtr op

alias exec dsip debug ccsip all

alias exec connections sh voip rtp connections

alias exec lastcall sh call hist voice last 1

!

line con 0

password xxx

login

transport preferred all

transport output all

speed 38400

line aux 0

transport preferred all

transport output all

line vty 0 4

password xxx

login

transport preferred all

transport input all

transport output all

!

end

I'm getting cause 500-Internal Server Error and cause 34-no circuit. When i try to test a call using sip i see logs of my last call, but when try using h323 i see none. My point is what could be the reason why can't i make a calls. All the framings and line codings specified by our provider (hdb3, r2 signalling, no crc) are already specified in my config.

So you have Slip Secs...

I'm thinking if you need this command: network-clock-select

its no use. im still getting no circuit error. what else? and i issue a command show voice port summary, it shows

IN OUT

PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC

========= == ============ ===== ==== ======== ======== ==

1/0:1 18 r2-digital up up seized idle y

Does it mean that our provider is blocking our calls?

I had issues with R2 that cleared up when rebooting. Turned out - IOS bug.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: