Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

how to configure "pa-vxc-2te1+"?

hi,all

pls tell me how to configure "pa-vxc-2te1+" card at cisco7206vxr. the card is used to connected to pstn.

Sincerely

Best Regards

Jason

3 REPLIES
Cisco Employee

Re: how to configure "pa-vxc-2te1+"?

New Member

Re: how to configure "pa-vxc-2te1+"?

thanks for your help first. but i still have question need to be solved. I haven't see the two interfaces in cisco7206vxr when it boot up. i just see only one interface displayed at "show run". the interface is "dspint DSPfarm2/0". i can't find out the other interface that i don't know whether can be remarked as "dspint DSPfarm2/1". why can't i find out the other interface?the related information is following:

------------------ show running-config ------------------

Building configuration...

Current configuration : 1076 bytes

!

version 12.2

no parser cache

no service single-slot-reload-enable

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname Router

!

boot system disk0:c7200-js-mz.122-2.T.bin

logging rate-limit console 10 except errors

!

dspint DSPfarm2/0

!

ip subnet-zero

!

!

!

ip cef

no ip dhcp-client network-discovery

call rsvp-sync

!

show version is:

------------------ show version ------------------

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-JS-M), Version 12.2(2)T, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Sat 02-Jun-01 11:19 by ccai

Image text-base: 0x600089C0, data-base: 0x61814000

ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)

BOOTFLASH: 7200 Software (C7200-KBOOT-M), Version 12.1(8a)E, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Router uptime is 3 minutes

System returned to ROM by reload at 03:01:49 UTC Tue Apr 22 2003

System image file is "disk0:c7200-js-mz.122-2.T.bin"

cisco 7206VXR (NPE400) processor (revision A) with 114688K/16384K bytes of memory.

Processor board ID 26813769

R7000 CPU at 350Mhz, Implementation 39, Rev 3.3, 256KB L2, 4096KB L3 Cache

6 slot VXR midplane, Version 2.6

Last reset from power-on

Channelized E1, Version 1.0.

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

Primary Rate ISDN software, Version 1.1.

2 FastEthernet/IEEE 802.3 interface(s)

4 Serial network interface(s)

8 Channelized E1/PRI port(s)

1 Voice resource(s)

125K bytes of non-volatile configuration memory.

46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).

8192K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x102

Gold

Re: how to configure "pa-vxc-2te1+"?

It's a common trip-up when you first use the new interfaces that can dynamically become T1 or E1. I called TAC on that one myself, the first time I touched one. Before controllers will appear to be configured, you must set the type using the "card type" command. Check a little deeper into the URL posted by tepatel:

http://www.cisco.com/univercd/cc/td/doc/product/core/cis7505/portadpt/voice_pa/pa_t1_e1/3592conf.htm#1047140

178
Views
0
Helpful
3
Replies
CreatePlease login to create content