Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

mgcp gateway caller id

I have installed a 2650XM 2.3(7)T and I have not been able to get incoming caller id to work. I have voice-port caller-id enabled

The following is my config.

Current configuration : 1310 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname PresRes-RTR

!

boot-start-marker

boot-end-marker

!

enable secret xxxx.

!

no network-clock-participate slot 1

no network-clock-participate wic 0

no aaa new-model

ip subnet-zero

no ip routing

no ip cef

!

!

!

!

no ftp-server write-enable

voice-card 1

!

!

!

!

!

!

!

!

!

!

!

!

!

ccm-manager redundant-host 10.12.0.2

ccm-manager mgcp

!

!

!

!

interface FastEthernet0/0

ip address 10.12.0.20 255.255.255.0

no ip route-cache

duplex auto

speed auto

no mop enabled

!

ip classless

ip route 0.0.0.0 0.0.0.0 10.12.0.254

ip http server

!

!

!

!

control-plane

!

!

!

voice-port 1/0/0

caller-id enable

!

voice-port 1/0/1

caller-id enable

!

voice-port 1/1/0

caller-id enable

!

voice-port 1/1/1

caller-id enable

!

mgcp

mgcp call-agent 10.12.0.1 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

!

mgcp profile default

!

!

!

!

dial-peer voice 1 pots

application mgcpapp

port 1/0/0

!

dial-peer voice 2 pots

application mgcpapp

port 1/0/1

!

dial-peer voice 3 pots

application mgcpapp

port 1/1/0

!

dial-peer voice 4 pots

application mgcpapp

port 1/1/1

!

!

line con 0

line aux 0

line vty 0 4

password xxxx

login

!

!

!

end

4 REPLIES
New Member

Re: mgcp gateway caller id

Some basic things come up in my head...

Is the callmanager configure with "CALLER-ID ENABLE" ?

Maybe you should configure the command "cptone X" on voice-ports and then configure "caller-id" under dial-peers...

New Member

Re: mgcp gateway caller id

Hi -

Last I knew, CallerID with MGCP and FXO is NOT possible. If you need CallerID, change the gateway to H.323

Not sure if this changed in IOS 12.3... Did this change?

-Jaret

New Member

Re: mgcp gateway caller id

I have changed it to H.323 and have it working now. I am trying to find the parameter to shorten the disconnect time. When the call at the other end disconnects, it takes about 10 seconds for the ipphone to hangup, can that be shorten. I have tried call disconnec time out / wait release timeout / and suervisory disconnect/ none seem to have worked so far.

New Member

Re: mgcp gateway caller id

Hi -

That is a very common issue, its reffered to as call supervision. The best way to resolve this is to change your analog lines to Ground Start instead of Loop Start.

Check out:

http://www.cisco.com/en/US/partner/tech/tk652/tk653/technologies_tech_note09186a00800ae2d1.shtml

-Jaret

290
Views
5
Helpful
4
Replies
CreatePlease login to create content