cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1712
Views
0
Helpful
3
Replies

Odd matched dial-peer on incoming call

pavelsh_ucs
Level 1
Level 1

Hi guys,

I really don't understand what's going on. Maybe I'm wrong, maybe not. But.

I got a call on my voice-port 0/2/0. But my cisco matches the wrong dial-peer. This dial-peer matches by trunk group "common" which has port 0/0/1-0/0/3 (0/2/0 is not a member of the trunk group). Is it bug or feature?

cnx-rr01#sh voice call st

CallID     CID  ccVdb      Port        Slot/DSP:Ch  Called #   Codec    MLPP Dial-peers

0xAD       152D 0x4AD5FF38 0/2/0            0/1:1   4255550103 g711ulaw 102/501

1 active call found

cnx-rr01#sh voice port s | i fxo

0/0/0           --  fxo-ls      up    dorm idle     on-hook  y

0/0/1           --  fxo-ls      up    dorm idle     on-hook  y

0/0/2           --  fxo-ls      up    dorm idle     on-hook  y

0/0/3           --  fxo-ls      down  down idle     on-hook  y

0/2/0           --  fxo-ls      up    up   idle     off-hook y

0/2/1           --  fxo-ls      up    dorm idle     on-hook  y

0/2/2           --  fxo-ls      up    dorm idle     on-hook  y

0/2/3           --  fxo-ls      down  down idle     on-hook  y

cnx-rr01#sh run | sec dial-peer voice 102

dial-peer voice 102 pots

trunkgroup common

tone ringback alert-no-PI

description ToPSTN

translation-profile incoming IN

translation-profile outgoing OUT00

preference 10

destination-pattern 9T

forward-digits all

cnx-rr01#sh trunk group common

Trunk group: common

        Description:

        trunk group label: common

        Translation profile (Incoming):

        Translation profile (Outgoing):

        LPCOR (Incoming):

        LPCOR (Outgoing):

        Preemption is disabled (by default)

        Hunt Scheme is round-robin

        Max Calls (Incoming):   NOT-SET (Any)   4 (Voice)       NOT-SET (Data)

        Max Calls (Outgoing):   NOT-SET (Any)   4 (Voice)       NOT-SET (Data)

        Max Calls (MixTotal):   NOT-SET (Any)   4 (Voice)       NOT-SET (Data)

        Retries: 0

        Trunk 0/0/1     Preference DEFAULT

                Member Timeslots : 1

                Total channels available : 1

                Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 1

        Trunk 0/0/2     Preference DEFAULT

                Member Timeslots : 1

                Total channels available : 1

                Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 1

        Trunk 0/0/3     Preference DEFAULT

                Member Timeslots : 1

                Total channels available : 0

                Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 0

        Total calls for trunk group: Data = 0, Voice = 0, Modem = 0

                                     Pend = 0, Free = 2

        advertise_flag 0x00000040, capacity timer 25 sec tripl_config_mask 0x00000000

        AC_curr 2, FD_curr 0, SD_curr 0

        succ_curr 19 tot_curr 19

        succ_report 19 tot_report 19

        changed 1 replacement position 0

        Current trunk : 0/0/1

3 Replies 3

rhopkins
Level 1
Level 1

Can you post the voice-port configuration?

Sent from Cisco Technical Support iPhone App

Hi Russel,

Sure:

cnx-rr01#sh run | sec voice-port 0/2/0

voice-port 0/2/0

supervisory custom-cptone CN-BELLCORE

cptone CN

timeouts call-disconnect 1

timeouts wait-release 1

connection plar opx 914255550103

description +86 400 XXXXXXX - Support IVR

station-id name China Support

station-id number +86XXXXXXXXXX

caller-id enable

Guys, do you have any thoughts by the chance?