Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

show dial-peer voice summary

Hi,

what is the meaning of "OUT STAT" column in

"show dial-peer voice summary"

command output and why does it show "down" for outgoing pots dial-peer?

Router#sh dial-peer voice summary

dial-peer hunt 0

AD PRE PASS OUT

TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT PORT

100 voip up up 0 syst

101 pots up up .T 0 down 2:D

102 pots up up 0 down 3:D

dial-peer voice 100 voip

description incoming

incoming called-number .T

session protocol sipv2

!

dial-peer voice 101 pots

destination-pattern .T

no digit-strip

port 2:D

forward-digits all

!

dial-peer voice 102 pots

incoming called-number .T

port 3:D

14 REPLIES
Hall of Fame Super Gold

Re: show dial-peer voice summary

New Member

Re: show dial-peer voice summary

No, thats not the case.

Above document has an example output of that command with no mention of OUT STAT column and there is no mention what OUT STAT may mean.

The Operational Status (column labeled OPER) in my case shows "up"

New Member

Re: show dial-peer voice summary

Hi

Use the command sh isdn status and see what is the output . I suppose ur D channel is down so u require the configure the D channel correctly

( for further update past ur " sh isdn st and run con )

regards

New Member

Re: show dial-peer voice summary

yes, thanks. figured that out already. ISDN was down indeed

Cisco Employee

Re: show dial-peer voice summary

Just some history on the OUT STAT...was added to address CSCdz87204 and added to images starting around 12.3(9).

An enhancement was done

by not selecting POTS dial-peers with end-point(s) in "DOWN" state during the outbound dial-peer matching.

Also, a new command line is added to enable or disable this new outbound dial-peer filtering functionality.

[default | no] dial-peer outbound status-check pots

By default, the dial-peer outbound status will be checked during the outbound dial-peer matching which is applied to any POTS dial-peer except ephone dial-peer.

If no option is specified in this command line, it will disable the dial-peer outbound status checking.

The display of "show dial-peer voice summary" and "show dial-peer voice " commands are modified to show the current POTS dial-peer outbound status.

How to determine the outbound status of a POTS dial-peer:

1. DOWN if DP Oper Status is DOWN

2. DOWN if DP voice-port of is DOWN

3. DOWN if DP trunkgroup(s) and all of its trunks are DOWN

4. UP if DP Oper Status is UP and DP voice-port is UP

5. UP if DP Oper Status is UP and DP trunkgroup(s) and any of

if trunks are UP

CCO doc...

http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_command_reference_chapter09186a00801a7f23.html#wp1459139

New Member

Hi scpage, Does this command

Hi scpage,

 

Does this command "show dial-peer voice summary" display SIP trunks too? I am working with a Voip gateway without CUBE. Will it be applicable to me?

 

Also OUT STAT will cover the scenario when the SIP Trunk is busyout right? I mean when the SIP trunk is busyout, the OUT STAT will display "no" correct?

 

Thanks,

Pandi

Silver

Pandiarajan,hope you doing

Pandiarajan,

hope you doing well..

OUT STAT Indicates the current OUTBOUND status of pots dial-peers only.

and if I understood your enquiry right. the SIP trunk which you talking about is VOIP dial-peer which will displayed its status in OPER column. and its the same for POTS dial-peers.

 

 

 

Please rate if its helpful

 
 

 

New Member

Thanks a lot Saif,This

Thanks a lot Saif,

This clarifies my doubt.

Silver

Pandiarajan,please click on

Pandiarajan,

please click on the correct answer so the question status will display answered question

Thanks

New Member

Hi Saif,I was searching for

Hi Saif,

I was searching for that, but I couldn't find such option. May be, the person who raised this question only have that option to mark the "correct answer". I gave 5 star rating.

 

Also, one of our voip expert says that OPER column is for operational status and not for SIP trunk status. Could you please give some example when we should use OPER column?

Silver

pandiarajan,I thought you

pandiarajan,

I thought you started this discussion, sorry about that.

OPER column referring to validity of the dial peers regardless of its type ( voip or pots ). so we are now talking about dial-peers validity in general and just like what your expert has been clarified.

dial-peers MUST meet one of these 3 elements to be VALIDE. which is

1- Destination-pattern and a voice-port or session target.      ... just like ...

()# dial-peer voice 123 pots

      destination-pattern 3333

      port 2/3

 

2- Incoming called-number.    ... just like ...

()# dial-peer voice 123 voip

       incoming-called number 33..

 

 

3- Answer-address.      ... just like...

()# dial-peer voice 123 pots

      answer address 3333

 

and that’s if any dial-peer not meets the above criteria... then its not considered to a router to be UP in OPER column. and we can for sure display that with the command # sh dial-peer voice summary

 

Hoping I could clarified the idea..

 

Regards

 

 

 

 

New Member

Thanks a lot Saif. That's

Thanks a lot Saif. That's very kind of you. It really helps me. 

 

Also regarding the point, VALID, which means, how the gateway will validate?

in the 2nd example, 

dial-peer voice 123 voip

       incoming-called number 33..

In this case, the gateway will validate the dial-peer based on the incoming-called number which must be a number not alpha numeric right? Could you please give me an example when the dial-peer configuration become invalid?

 

One more doubt on your first example "session-target 3333", I was always under the impression that only voip dial-peers got session-target as IPAddress or ServerName. But in this case we do have pots dial-peers too. In this case the "3333" is a destination address of some gateway or CUCM?

 

Thanks again,

Pandi

Silver

Pandi,I made a mistake in the

Pandi,

I made a mistake in the above example (the first) and already change it. sorry about that. I was in rush of being in touch with colleagues at work and posting here. anyway...

dial-peers have two types...

the first is VOIP-db which sends or receive voice calls to/from IP networks.

the second is POTS-db which sends or receive voice calls to/from analog networks.

with the first type we obliged to use the command ( session-target ipv4 ) because its the only command that allows me to use ipv4 protocol as a target destination for the travelling voice call.

while the second type allows me to send the voice calls to a destination targets that primarily dose not have tcp/ip protocol.

 

about validity...

routers needs to validate dial-peers already configured inside it to be able to choose which path is the best for the call to be sent. and thus. the dial-peer must meet one of the 3 elements which mentioned above to be valid. otherwise its considered by the router as invalid or DOWN as it will be shown in OPER column if we issue the command ()# sh dial-peer voice summary.

 

Greetings

New Member

Now I am very clear. Thanks a

Now I am very clear. Thanks a lot Saif. I really appriciate the help.

 

Thanks again,

Pandi

9575
Views
35
Helpful
14
Replies
CreatePlease to create content