07-06-2008 06:53 AM
Hi,
I have one AS5400XM, it handles the sip calls and routes the call to providers. The first route is provider A, second is provider B, the last is provider C. I find that the call cannot overflow to provider B and C. any missing?
rgds
The dial-peer setting is
R1
dial-peer voice 6501 voip
description provider A
tone ringback alert-no-PI
service session
destination-pattern 65.
max-conn 108
session protocol sipv2
session target ipv4:192.168.12.32
dtmf-relay rtp-nte h245-signal h245-alphanumeric
!
dial-peer voice 6502 voip
description provider A
tone ringback alert-no-PI
service session
destination-pattern 65.
max-conn 108
session protocol sipv2
session target ipv4:192.168.12.33
dtmf-relay rtp-nte h245-signal h245-alphanumeric
!
dial-peer voice 6503 voip
description provider B
tone ringback alert-no-PI
service session
pref 1
destination-pattern 65.
max-conn 108
session protocol sipv2
session target ipv4:192.168.24.32
dtmf-relay rtp-nte h245-signal h245-alphanumeric
!
dial-peer voice 6504 voip
description provider B
tone ringback alert-no-PI
service session
pref 1
destination-pattern 65.
session protocol sipv2
session target ipv4:192.168.24.33
dtmf-relay rtp-nte h245-signal h245-alphanumeric
!
dial-peer voice 6505 voip
description provider C
tone ringback alert-no-PI
service session
pref 2
destination-pattern 65.
max-conn 108
session protocol sipv2
session target ipv4:192.168.36.32
dtmf-relay rtp-nte h245-signal h245-alphanumeric
!
dial-peer voice 6506 voip
description provider C
tone ringback alert-no-PI
service session
pref 2
destination-pattern 65.
max-conn 108
session protocol sipv2
session target ipv4:192.168.36.32
dtmf-relay rtp-nte h245-signal h245-alphanumeric
!
07-06-2008 09:08 AM
Hi, you need "no huntstop" configured for all the DPs.
Also note DP 6504 has no max-conn configured so it won't stop accepting calls there.
07-07-2008 07:39 AM
Hi,
The correct setting should be with "no huntstop". this setting can work in sip call. Does it support h323 call?
rdgs
R1
dial-peer voice 6501 voip
no huntstop
dial-peer voice 6502 voip
no huntstop
dial-peer voice 6503 voip
no huntstop
dial-peer voice 6504 voip
no huntstop
max-conn 108
dial-peer voice 6505 voip
no huntstop
dial-peer voice 6506 voip
no huntstop
07-07-2008 09:37 AM
Yes, most DP settings work the same no matter what the protocol used.
As an appreciation to those providing answers, please rate useful posts!
07-10-2008 09:00 AM
Hi,
If the proivder A sip servers down, does it overflow to the providers B? if so, which timer to control the overflow when first Dial-peer down?
e.g.
1 second, the call will overflow,
or 3 seconds later, the call will overflow
rdgs
07-10-2008 11:15 AM
Hi,
SIP timers and counters are configured under sip-ua.
07-11-2008 05:10 PM
Hi,
By default setting, the proivder A goes down, does the sip call flow to provider B base on the config?
rdgs
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide