cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1067
Views
0
Helpful
11
Replies

Voip: CLI is not being forwarded

rameezsardar
Level 1
Level 1

Dears,

I connected cisco 3800 router with ericsson MD110 exchange using QSIG over E1 Pri. Calls are forwarding properly over ip network but few features are not being enabled specially CLI feature. I found a documnet where a command "caller-id enable" was issue in voice-port interface. But i go in this mode using command voice-port 1/0:15, no command caller-id find. My topology is below:

MD110 PBX ----3845---------3825----MD110 PBX

Waiting for immediate positive response.

Regards

Rameez

1 Accepted Solution

Accepted Solutions

Hi,

you PBX is not sending calling number:

Calling Party Number i = 0x01A1, N/A

This can happen for example if the PBX was configured to be connected to PST and not send the calling number.

You need to have the PBX configured to send calling number. Unless this is done, router will never be able to display it.

View solution in original post

11 Replies 11

paolo bevilacqua
Hall of Fame
Hall of Fame

Hi,

do you have the following in config ? Note you need recent IOS like 12.4(11)XJ4 to enable this.

voice service voip

qsig decode

Hope this helps, please rate post if it does!

how come caller-id enable related to "voice service voip "

regards

pranab

Dear,

I am using c3845-spservicesk9-mz.123-11.T11.bin and command is not available under voice service voip.

Waiting for immediate response

Regards

As I mentioned you need to upgrade to 12.4(11)XJ4 , after that the command will be available, and should resolve your issue.

Dear, I upgraded my ios to c3845-adventerprisek9-mz.124-11.XJ4 and used command qsig decode on both side but phone didn't show cli....... I am waiting for you next suggestion.......

Best Regards

Rameez

Please take a trace with "debug isdn q931" and "term mon". Post the output here.

R1#

Oct 30 13:19:12.465: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3684

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA18381

Preferred, Channel 1

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0181, N/A

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81, '3'

Plan:ISDN, Type:Unknown

Shift to Codeset 5

Codeset 5 IE 0x31 i = 0x80

Shift to Codeset 5

Codeset 5 IE 0x32 i = 0x81

R1#

Oct 30 13:19:12.469: ISDN Se1/0:15 Q931: TX -> SETUP_ACK pd = 8 callref = 0xB684

Channel ID i = 0xA98381

Exclusive, Channel 1

Oct 30 13:19:13.005: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684

Called Party Number i = 0x81, '0'

Plan:ISDN, Type:Unknown

R1#

Oct 30 13:19:13.481: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684

Called Party Number i = 0x81, '0'

Plan:ISDN, Type:Unknown

Oct 30 13:19:14.429: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684

Called Party Number i = 0x81, '1'

Plan:ISDN, Type:Unknown

R1#

Oct 30 13:19:14.577: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xB684

Oct 30 13:19:14.693: ISDN Se1/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xB684

Facility i = 0x9FAA068001018201018B0100A1080201020201018000

Progress Ind i = 0x8188 - In-band info or appropriate now available

Oct 30 13:19:14.737: ISDN Se1/0:15 Q931: RX <- FACILITY pd = 8 callref = 0x3684

Facility i = 0x9FAA06800100820100A406020102810102

R1#

Oct 30 13:19:20.841: ISDN Se1/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xB684

Progress Ind i = 0x8182 - Destination address is non-ISDN

Connected Number i = 0x0181, '3001'

Shift to Codeset 5

Codeset 5 IE 0x32 i = 0x81

Oct 30 13:19:20.901: ISDN Se1/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x3684

R1#

Oct 30 13:19:32.625: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xB684

Cause i = 0x8190 - Normal call clearing

Oct 30 13:19:32.681: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x3684

Cause i = 0x8190 - Normal call clearing

Oct 30 13:19:32.681: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB684

R1#u all

All possible debugging has been turned off

R1#

Output of Router R2 you will find in my next post as i have to split output due to character limit.

Regards

R2#

R2#

.Oct 30 13:19:14.441: ISDN Se1/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x1, Calling num

.Oct 30 13:19:14.441: ISDN Se1/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x1, Called num 3001

.Oct 30 13:19:14.441: ISDN Se1/0:15 Q931: TX -> SETUP pd = 8 callref = 0x00A3

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Facility i = 0x9FAA068001018201018B0100A1080201350201008000

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x01A1, N/A

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81, '3001'

Plan:ISDN, Type:Unknown

.Oct 30 13:19:14.553: ISDN Se1/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x80A3

Channel ID i = 0xA98381

Exclusive, Channel 1

.Oct 30 13:19:14.565: ISDN Se1/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x80A3

.Oct 30 13:19:14.681: ISDN Se1/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x80A3

Facility i = 0x9FAA06800100820100A406020135810102

Progress Ind i = 0x8188 - In-band info or appropriate now available

Progress Ind i = 0x8182 - Destination address is non-ISDN

Shift to Codeset 5

Codeset 5 IE 0x32 i = 0x81

.Oct 30 13:19:14.737: ISDN Se1/0:15 Q931: TX -> FACILITY pd = 8 callref = 0x00A3

Facility i = 0x9FAA06800100820100A406020102810102

.Oct 30 13:19:20.829: ISDN Se1/0:15 Q931: RX <- CONNECT pd = 8 callref = 0x80A3

Progress Ind i = 0x8182 - Destination address is non-ISDN

Connected Number i = 0x0181, '3001'

Shift to Codeset 5

Codeset 5 IE 0x32 i = 0x81

.Oct 30 13:19:20.829: ISDN Se1/0:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x00A3

.Oct 30 13:19:32.605: ISDN Se1/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x80A3

Cause i = 0x8190 - Normal call clearing

.Oct 30 13:19:32.605: ISDN Se1/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x00A3

.Oct 30 13:19:32.637: ISDN Se1/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x80A3

R2#

R2#u all

All possible debugging has been turned off

R2#

Note: Call initiated from R1 to R2.

Best Regards

Rameez

Dear,

Still waiting for your response..

Best Regards

Rameez

Hi,

you PBX is not sending calling number:

Calling Party Number i = 0x01A1, N/A

This can happen for example if the PBX was configured to be connected to PST and not send the calling number.

You need to have the PBX configured to send calling number. Unless this is done, router will never be able to display it.

Thanks buddy for your help. Yes that was the issue because pbx was not sending calling id. pbx operator did some configuration and it started working. But for you information, calling number keep visible on display even if i configure command "no qsig decode" in voice service voip mode..Thanks again...

Regards

Rameez

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: