Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Voip DIal-peer Problem pls. help

My Head office PBX is connected to my Voice Router with 12 (VIC2-2E&M x 6 card) E&M Port and my Remote office-1 & 2 are the same.

My requirement:

1. HO dial to access code 60, then get a second dial tone and dial RO-1 PBX number (3000-3500)

2. HO dial to access code 80, then get a second dial tone and dial RO-2 PBX number (3000-3500)

Ext2000---PBX--E&M---HO-router-WAN---RO-1router---E&M---PBX---Ext3000

Ext2001---PBX--E&M---HO-router-WAN---RO-2router---E&M---PBX---Ext3000

Ho config:

voice-port 0/0/0 for RO-1

type 5

signal immediate

dial-type pulse

voice-port 0/0/1 for RO-2

type 5

signal immediate

dial-type pulse

dial-peer voice 100 pots

destination-pattern .T

port 0/0/0

dial-peer voice 101 voip

destination-pattern .T

session target ipv4:172.16.1.2

dial-peer voice 200 pots

destination-pattern .T

port 0/0/1

dial-peer voice 201 voip

destination-pattern .T

session target ipv4:192.168.1.100

RO-1 config:

voice-port 0/0/1

type 5

signal immediate

dial-type pulse

dial-peer voice 300 pots

destination-pattern .T

port 0/0/1

dial-peer voice 301 voip

destination-pattern .T

session target ipv4:172.16.1.1

RO-2 config:

voice-port 0/0/1

type 5

signal immediate

dial-type pulse

dial-peer voice 400 pots

destination-pattern .T

port 0/0/1

dial-peer voice 401 voip

destination-pattern .T

session target ipv4:192.168.1.101

Problem:

In HO both dial-peer voip has same destination-pattern. My both remote office has same extension number. So, how can I separate the calls of RO-1 & RO-2 ?

  • Voice over IP
2 REPLIES

Re: Voip DIal-peer Problem pls. help

If you configure the PBX to send the access code along with the extension, then you could have dial peers such as:

dial-peer voice 101 voip

destination-pattern 60....

session target ipv4:172.16.1.2

dial-peer voice 201 voip

destination-pattern 80....

session target ipv4:192.168.1.100

Hope this helps. If so, please rate the post.

Brandon

New Member

Re: Voip DIal-peer Problem pls. help

Thanks for your reply. I have already solved the problem. Here is the config:

Ho config:

voice-port 0/0/0 for RO-1

type 5

signal immediate

dial-type pulse

connection Tie-line 60

voice-port 0/0/1 for RO-2

type 5

signal immediate

dial-type pulse

connection Tie-line 80

dial-peer voice 100 pots

destination-pattern 70T

port 0/0/0

dial-peer voice 101 voip

destination-pattern 60T

session target ipv4:172.16.1.2

dial-peer voice 200 pots

destination-pattern 75T

port 0/0/1

dial-peer voice 201 voip

destination-pattern 80T

session target ipv4:192.168.1.100

RO-1 config:

voice-port 0/0/1

type 5

signal immediate

dial-type pulse

connection Tie-line 70

dial-peer voice 300 pots

destination-pattern 60T

port 0/0/1

dial-peer voice 301 voip

destination-pattern 70T

session target ipv4:172.16.1.1

RO-2 config:

voice-port 0/0/1

type 5

signal immediate

dial-type pulse

connection Tie-line 75

dial-peer voice 400 pots

destination-pattern 80T

port 0/0/1

dial-peer voice 401 voip

destination-pattern 75T

session target ipv4:192.168.1.101

Here RO-1 come HO by access code 70 & RO-2 come HO by access code 75. All of my PBX have some 1, 2 & 3 digit extension number.

Pls. check my configure.

183
Views
0
Helpful
2
Replies
This widget could not be displayed.