Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Another FAC post

Hi Guys,


I am having problems with using FAC on the UC520.


I have two ephone-dn's. One that is supposed to enter the authorization code and the other that is a vip caller (no auth codes).


I  am able to get the prompt for the user that is restricted and once  entered correctly the outgoing called is dialed. However the problem is that I  am also getting the prompt for the ephone that is setup to be the vip  caller. I've tried several different scenarios but can't seem to get it  work.


Essentially my goal is such that vip caller hits  the 60 pots dial peer immediately and the auth code call hits the 5500  voip dial peer then once entered correctly goes to the 60 pots dial  peer.


Thanks for any assistance in advance.


Below is my config:


dial-peer cor custom

  name internal

  name local

  name local-fac

!

dial-peer cor list call-internal

  member internal

!

dial-peer cor list call-local

  member local

!

dial-peer cor list user-local

  member internal

  member local

  member emergency

  member toll-free

!

dial-peer cor list call-local-fac

  member local-fac

!

dial-peer cor list user-local-fac

  member internal

  member local-fac

!

application

  service clid_authen_collect

   param uid-len 3

   param pin-len 3

!

aaa new-model

aaa authentication login h323 local

aaa authorization exec h323 local

aaa authorization network h323 local

!

username 201 password 123

username 201 autocommand exit

!

dial-peer voice 5500 voip

  corlist incoming call-local-fac

  description Local Calls

  service clid_authen_collect

  destination-pattern 9[2-9]......

  session target ipv4:10.1.1.1

  incoming called-number 9[2-9]......

  dtmf-relay h245-alphanumeric

  codec g711ulaw

  no vad

!

dial-peer voice 60 pots

  trunkgroup ALL_FXO

  corlist outgoing call-local-fac

  description Local Calls

  translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

  destination-pattern 9[2-9]......

  forward-digits all

  no sip-register

!

ephone-dn 10

  corlist outgoing user-local

!

ephone-dn 12

  corlist outgoing user-local-fac

1 ACCEPTED SOLUTION

Accepted Solutions
Community Member

Re: Another FAC post

Try making these changes and test-

ephone-dn 10
  corlist incoming user-local

ephone-dn 12
  corlist incoming user-local-fac

dial-peer voice 5500 voip
  corlist outgoing call-local-fac
  corlist incoming call-local

dial-peer voice 60 pots
  corlist outgoing call-local

Thanks,

Anthony

5 REPLIES
Community Member

Re: Another FAC post

Try making these changes and test-

ephone-dn 10
  corlist incoming user-local

ephone-dn 12
  corlist incoming user-local-fac

dial-peer voice 5500 voip
  corlist outgoing call-local-fac
  corlist incoming call-local

dial-peer voice 60 pots
  corlist outgoing call-local

Thanks,

Anthony

Community Member

Re: Another FAC post

Hi Anthony,


Thanks for the response.


This actually did work. The main problem was the fact that under the dn's I had put outgoing instead of incoming (lack of sleep, I think).

BTW, If I wanted to do this same process with the international dial-peer, how is the best way to handle the ephone-dn's in this case? We have 9011T and 91[2-9][2-9][2-9]....... as international numbers here.


Thanks again for the assistance.


Community Member

Re: Another FAC post

I'll take a closer look and get back to you

(mobile)

Community Member

Re: Another FAC post

Added user-international under the vip callers ephone-dn

Remaining users won't really need to dial international calls out.

Thanks again Anthony.

Best Regards.

Community Member

Re: Another FAC post

When I first read this post on my mobile this afternoon I thought the previous recommendations didn't fix the issue. Good to hear you're all set.

Thanks,

Anthony

339
Views
0
Helpful
5
Replies
CreatePlease to create content