Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

MeetMe Conference: Get "No Conference Bridge" after pressing MeetMe softkey and conference extension...

Configured MeetMe using the UC500_Meetme_Conferencing.pdf document.  After pressing the MeetMe softkey and entering 600 (conference extension) get a busy tone and message on phone that says "No Conference Bridge".   Here is my MeetMe Configuration below....

voice-card 0
no dspfarm
dsp services dspfarm
.

.

.

.

sccp local Loopback0
sccp ccm 10.1.1.1 identifier 1 version 4.0
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register 1234567890
!
dspfarm profile 1 conference 
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 1
associate application SCCP
!
.

.

.

.

telephony-service
sdspfarm units 5
sdspfarm tag 1 1234567890
conference hardware

.

transfer-system full-consult

.

.

.

.

ephone-template  9
softkeys idle  Redial HLog Cfwdall Newcall Pickup Dnd
softkeys seized  Redial Cfwdall Pickup Callback Meetme
softkeys connected  Hold Trnsfer TrnsfVM Endcall Park Confrn ConfList RmLstC LiveRcd Select Join
.

.

.

.

ephone-dn  95  dual-line
number 550
conference meetme
no huntstop
!
!
ephone-dn  96  dual-line
number 550
conference meetme
preference 1
no huntstop
!
!
ephone-dn  97  dual-line
number 550
conference meetme
preference 2
no huntstop
!
!
ephone-dn  98  dual-line
number 550
conference meetme
preference 3
no huntstop
!

.

.

.

ephone  23
conference admin
device-security-mode none
video
mac-address 001C.5840.E771
ephone-template 9
username "tarea" password password
paging-dn 1
type 7940
button  1:29 2s55
night-service bell
!

7 REPLIES
Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

What is the output from "show dspfarm all"???

It should be something like:

Dspfarm Profile Configuration

  Profile ID = 2, Service = CONFERENCING, Resource ID = 2  

Profile Description :  

Profile Admin State : UP 

Profile Operation State : ACTIVE 

Application : SCCP   Status : ASSOCIATED 

Resource Provider : FLEX_DSPRM   Status : UP 

Number of Resource Configured : 2 

Number of Resource Available : 2

Codec Configuration 

Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required 

Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required

Regards
Eivind


Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

UC520#show dspfarm all
Dspfarm Profile Configuration

Profile ID = 1, Service = CONFERENCING, Resource ID = 1
Profile Description :
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : RESOURCE ALLOCATED
Application : SCCP   Status : NOT ASSOCIATED
Resource Provider : FLEX_DSPRM   Status : UP
Number of Resource Configured : 1
Number of Resource Available : 1
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required


SLOT DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0    4   23.8.0   UP     N/A  FREE  conf   1      -         -         -

Total number of DSPFARM DSP channel(s) 1

Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

Check out http://uc500.com/files/CME-4-1-HW-Conf-Tech-Tip.pdf

Regards

Eivind

Are you sure you issued a "no shutdown" underneath the dspfarm profile?? When you create the profile, it automatically go to "shutdown".

Message was edited by: Eivind Jonassen

Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

That worked!  Thank you!

Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

I made the same mistake the first time I created the profile as well :)

Glad I could help.

Regards

Eivind

Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

I've configured another box before using 1 as the profile number, and it worked fine.   Maybe the instructions on how to set it up should be modified to use 100 instead of 1.

Community Member

Re: MeetMe Conference: Get "No Conference Bridge" after pressing

Hi,

It actually does in the guide CME-4-1-HW-Conf-Tech-Tip.pdf.

Regards

Eivind

5427
Views
0
Helpful
7
Replies
CreatePlease to create content