Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

UC 560 FXO

Hi, I'm new here. I have UC 560 FXO, 2 Cisco 2900 Router,2  Cisco Catalyst 3560 V2 series PoE-48 and 4 tel Cisco 7942. I want to create a VoIP network from point A to point B ; where I can find all settings, connections and configuration commands for these?

Thank you,

Adrian.

2 ACCEPTED SOLUTIONS

Accepted Solutions
New Member

UC 560 FXO

Hello,

Cisco Configuration Assitant Admin Guide(this will be for the UC): http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_assistant/version3_2_1/administration_guide/cca_sbcs_admin_guide.pdf

Cisco IOS CLI for Initial Configuration(for 2900 series router)

http://www.cisco.com/en/US/docs/routers/access/1900/software/configuration/guide/appendixAcli_external_docbase_0900e4b1810581a6_4container_external_docbase_0900e4b181547f63.html

3560 Configuration Guides(find the one that matches your IOS)

http://www.cisco.com/en/US/products/hw/switches/ps5528/products_installation_and_configuration_guides_list.html

Please note, the UC will be the voice gateway, so you would only really need the 2900 series routers for internet/LAN routing, not voice. You will want to configure the UC and 3560 connection as an 802.1q trunk, tagging the voice vlan. For access ports on the 3560 make sure you have the following command for the phones: switchport voice vlan 100

Thanks,

-john

New Member

UC 560 FXO

Hello,

I would certainly think so. You just need a route on the 3560s to the network at point B.

Thanks,

-john

7 REPLIES
New Member

UC 560 FXO

Hello,

Cisco Configuration Assitant Admin Guide(this will be for the UC): http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_assistant/version3_2_1/administration_guide/cca_sbcs_admin_guide.pdf

Cisco IOS CLI for Initial Configuration(for 2900 series router)

http://www.cisco.com/en/US/docs/routers/access/1900/software/configuration/guide/appendixAcli_external_docbase_0900e4b1810581a6_4container_external_docbase_0900e4b181547f63.html

3560 Configuration Guides(find the one that matches your IOS)

http://www.cisco.com/en/US/products/hw/switches/ps5528/products_installation_and_configuration_guides_list.html

Please note, the UC will be the voice gateway, so you would only really need the 2900 series routers for internet/LAN routing, not voice. You will want to configure the UC and 3560 connection as an 802.1q trunk, tagging the voice vlan. For access ports on the 3560 make sure you have the following command for the phones: switchport voice vlan 100

Thanks,

-john

UC 560 FXO

Hi,

thanks for your response; actually, between point A and point B I have a Over The Air bridged IP traffic provided by 2 RF 7800 M MP Harris Multiband Radios ( an IP Network between each other); in this case, I still need 2900 ?

Thanks,

Adi.

New Member

UC 560 FXO

Hello,

I'm not very familiar with the point to point wireless bridges you have. What function are the 2900s serving? If they are just acting as layer 3 gateways, then I would think the 3560s could do that function.

How To Configure InterVLAN Routing on Layer 3 Switches

http://www.cisco.com/en/US/tech/tk389/tk815/technologies_configuration_example09186a008019e74e.shtml

Thanks,

-john

UC 560 FXO

Hi,

in this case, if the 3560s do that function, can I connect to 3560 a PC for data exchange with another PC on point B?

Thanks,

Adi.

New Member

UC 560 FXO

Hello,

I would certainly think so. You just need a route on the 3560s to the network at point B.

Thanks,

-john

UC 560 FXO

Hi,

thank you very much for your support. Maybe if I stiil need help, you can help me again.

Thanks,

Adrian.

dragan_adrian_remus@yahoo.com

UC 560 FXO

Hello,

I have this situation now: in point A, I have UC 560, switch 3560 v2 PoE 48, 2 Cisco Ip phones ; in point B, I have switch 3560 v2 PoE 48, 2 Cisco Ip phones. All equipment is configured and functional; the switches are connected through straight cable, between fa 0/2. Vlan's are configured too; interface fa 0/2 (3560) trunked.

Instead of connecting cable, I'll have a radionetwork. The ends of this radionet are in different subnets, but one are the same with one 3560(the one connected with UC 560). So, I'll need to interpose two 2901. Please tell me the settings for these routers.

Regards,

Adrian

962
Views
0
Helpful
7
Replies
CreatePlease to create content