Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

ASA 8.0 (EZVPN Server) router2821 (EZVPN remote) , Not working

I am configurin my ASA as an EZVPN server. This is the configuration:

tunnel-group Redes type remote-access

tunnel-group Redes general-attributes

address-pool RedesPool

default-group-policy Redes

tunnel-group Redes ipsec-attributes

pre-shared-key *

tunnel-group VPNROUTERS type remote-access

tunnel-group VPNROUTERS general-attributes

default-group-policy VPNROUTERS

tunnel-group VPNROUTERS ipsec-attributes

pre-shared-key *

isakmp ikev1-user-authentication none

group-policy VPNROUTERS internal

group-policy VPNROUTERS attributes

vpn-tunnel-protocol IPSec

secure-unit-authentication disable

nem enable

address-pools none

ipv6-address-pools none

group-policy Redes internal

group-policy Redes attributes

dns-server value 10.1.4.2 10.1.4.3

vpn-tunnel-protocol IPSec

password-storage disable

default-domain value mf.gov.ve

I am configurin a router as EZVPN client. This is the configuration:

crypto isakmp policy 10

encr 3des

hash md5

authentication pre-share

group 2

!

!

!

!

!

crypto ipsec client ezvpn VPNROUTERS

connect manual

group VPNROUTERS key router1

mode network-extension

peer 200.11.187.58

acl 101

xauth userid mode interactive

!

The VPN negotiation gets stuck at this level:

*Sep 20 19:59:46.119: ISAKMP:(0:255:SW:1):Need config/address

*Sep 20 19:59:46.119: ISAKMP:(0:255:SW:1):Need config/address

*Sep 20 19:59:46.19: ISAKMP:(0:255:SW:1):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

*Sep 20 19:59:46.119: ISAKMP:(0:255:SW:1):Old State = IKE_P1_COMPLETE New State = IKE_CONFIG_MODE_REQ_SENT

*Sep 20 19:59:46.123: ISAKMP (0:134217983): received packet from 200.11.187.58 dport 500 sport 500 Global (I) CONF_ADDR

*Sep 20 19:59:46.123: ISAKMP: set new node -1061602860 to CONF_ADDR

%SYS-3-CPUHOG: Task is running for (6004)msecs, more than (2000)msecs (0/0),process = Crypto IKMP.

-Traceback= 0x40275E38 0x41245068 0x4124876C 0x41248884 0x427BAA00 0x427BD900 0x427BB2C4 0x427BBC48 0x427BC5F0 0x427B5354 0x427D5A84 0x42C9EDD0 0x427D801C 0x427A9244 0x427AAC2C 1

*Sep 20 19:59:46.119: ISAKMP:(0:255:SW:1):Old State = IKE_I_AM1 New State = IKE_P1_COMPLETE

Since i am configuring network extension, i am not suppouse to get conf_addr state.

I do not know why i am getting this state.

2 REPLIES
Silver

Re: ASA 8.0 (EZVPN Server) router2821 (EZVPN remote) , Not worki

Add the following lines to your group-policy VPNROUTERS attributes

vpn-access-hours none

vpn-simultaneous-logins 3

vpn-idle-timeout 30

vpn-session-timeout none

vpn-filter none

ipsec-udp enable

ipsec-udp-port 10000

split-tunnel-policy tunnelall

split-tunnel-network-list none

default-domain none

Following link may help you

http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080809222.shtml

New Member

Re: ASA 8.0 (EZVPN Server) router2821 (EZVPN remote) , Not worki

Try this:

tunnel-group VPNROUTERS general-attributes

address-pool RedesPool

!

Just beat my head on this one last night and finally this morning I found out that since it's a client (even though hardware client) you need to give it IP address.

255
Views
0
Helpful
2
Replies
CreatePlease to create content