Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

ASA VPN Tunnel won't encrypt pkts

So I'm having issues getting data to come across this site to site tunnel.  The remote site needs us to NAT the destination network because they have an overlap.  I hope this makes sense.

Remote Endpoint - A.A.A.A

Remote LAN - 156.30.x.x

Local Endpoint - B.B.B.B

Local LAN - 10.0.202.183 which is NAT'd to 192.168.10.45 because that overlaps on their side

Details are below.  Thanks for the help.

My ASA info.

tunnel-group B.B.B.B type ipsec-l2l

tunnel-group B.B.B.B ipsec-attributes

pre-shared-key *****

crypto map L2L-map 1 match address outside_1_cryptomap

crypto map L2L-map 1 set pfs

crypto map L2L-map 1 set peer B.B.B.B

crypto map L2L-map 1 set transform-set ESP-3DES-SHA

static (outside,inside) 192.168.10.45 10.0.202.183 netmask 255.255.255.255

access-list outside_1_cryptomap extended permit ip host 10.0.202.183 156.30.x.x 255.255.255.248

sho crypto ipsec sa output -

    Crypto map tag: L2L-map, seq num: 1, local addr: 66.196.49.130

      access-list outside_1_cryptomap extended permit ip host 10.0.202.183 156.30.x.x 255.255.255.248

      local ident (addr/mask/prot/port): (10.0.202.183/255.255.255.255/0/0)

      remote ident (addr/mask/prot/port): (156.30.x.x/255.255.255.248/0/0)

      current_peer: B.B.B.B

      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0

      #pkts decaps: 3483, #pkts decrypt: 3483, #pkts verify: 3483

      #pkts compressed: 0, #pkts decompressed: 0

      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0

      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0

      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0

      #send errors: 0, #recv errors: 0

      local crypto endpt.: A.A.A.A, remote crypto endpt.: B.B.B.B

      path mtu 1500, ipsec overhead 58, media mtu 1500

      current outbound spi: 166C0F34

      current inbound spi : 0002F40E

    inbound esp sas:

      spi: 0x0002F40E (193550)

         transform: esp-3des esp-sha-hmac no compression

         in use settings ={L2L, Tunnel, PFS Group 2, }

         slot: 0, conn_id: 21278720, crypto-map: L2L-map

         sa timing: remaining key lifetime (kB/sec): (8210/10842)

         IV size: 8 bytes

         replay detection support: Y

         Anti replay bitmap:

          0xFFFFFFFF 0xFFFFFFFF

    outbound esp sas:

      spi: 0x166C0F34 (376180532)

         transform: esp-3des esp-sha-hmac no compression

         in use settings ={L2L, Tunnel, PFS Group 2, }

         slot: 0, conn_id: 21278720, crypto-map: L2L-map

         sa timing: remaining key lifetime (kB/sec): (8496/10842)

         IV size: 8 bytes

         replay detection support: Y

         Anti replay bitmap:

          0x00000000 0x00000001

sho crypto isa sa output -

5   IKE Peer: 216.203.80.118

    Type    : L2L             Role    : initiator

    Rekey   : no              State   : MM_ACTIVE

7 REPLIES
Cisco Employee

ASA VPN Tunnel won't encrypt pkts

Mate ,

as per your descreption :

Local LAN - 10.0.202.183 which is NAT'd to 192.168.10.45

if the lan at your side is 10.0.202.183 then you should be using a nat like this :

access-list NAT_WHEN_THROUGH_VPN permit ip h 10.0.202.183 <156.30>

static (inside,outside) 192.168.10.45 access-list NAT_WHEN_THRUGH_VPN

and the crypto map should be using the translated ip address :

access-list crypto permit  192.168.10.45

i assumed that the ip on the inside is : 10.0.202.183 and the other side sees this one as 192.168.10.45 .

hope that this helps .
MOhammad.

New Member

ASA VPN Tunnel won't encrypt pkts

That sounds about right.  The remote site is trying to ping/hit 10.0.202.183 which is what I'm trying to NAT to 192.168.10.45 (server) because they have an IP conflict.  I'll implement the changes you said and see what happens.

Re: ASA VPN Tunnel won't encrypt pkts

Hi there,

Please try this,

access−list policy−nat extended permit ip host 10.0.202.183 156.30.x.x 255.255.255.248

static (inside,outside) 10.0.255.0 access−list policy−nat

access-list outside_1_cryptomap extended permit ip 10.0.255.0 255.255.255.0 156.30.x.x 255.255.255.248

----------------------

Likewise from your remote-land's remote desitination (i.e. Local Lan) has be as follows

access-list outside_2_cryptomap extended permit ip 156.30.x.x 255.255.255.248 10.0.255.0 255.255.255.0

Hope that helps.

thanks

Rizwan Rafeek

Message was edited by: Rizwan Mohamed

New Member

ASA VPN Tunnel won't encrypt pkts

Well I don't know if that is the same as the above person, but we'l see.  Here's hoping.

New Member

ASA VPN Tunnel won't encrypt pkts

The remote side is trying to ping 10.0.202.183 since they already have a 192.168.10.45 on another VPN tunnel.  That's what I'm trying to figure out on the NAT side.

ASA VPN Tunnel won't encrypt pkts

"they already have a 192.168.10.45 on another VPN tunnel."

If you believe this IP "192.168.10.45" already in use then, natting this IP "192.168.10.45" is no good at all.

You can find another subnet available, so lets take subnet for an example "10.0.255.0 255.255.255.0".

So, based on this subnet, I will edit my above answer.

check it out.

thanks

Rizwan Rafeek  

New Member

ASA VPN Tunnel won't encrypt pkts

Sorry, this was confusing.  Basically my local lan IP that needs to be accessible over this tunnel is 192.168.10.45 and I need to translate that to 10.0.202.183 for the remote endpoint to hit because the remote endpoint has another tunnel up that is using 192.168.10.45 address.  So if the remote side pings 10.0.202.183, the 192.168.10.45 server on my local lan will respond.  I hope that makes sense.

672
Views
0
Helpful
7
Replies
CreatePlease to create content