Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

How can I configure using win7 L2TP connect ASA 8.3(1)?

config:

crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec transform-set TRANS_ESP_AES128_SHA esp-aes esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_AES128_SHA mode transport
crypto ipsec transform-set TRANS_ESP_AES256_SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_AES256_SHA mode transport
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 5 set transform-set TRANS_ESP_3DES_SHA ESP-3DES-SHA
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set transform-set TRANS_ESP_3DES_MD5 TRANS_ESP_AES128_SHA TRANS_ESP_AES256_SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp identity hostname
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp nat-traversal 30
crypto isakmp am-disable
tunnel-group DefaultRAGroup general-attributes
address-pool IP_L2TP_Pool
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
peer-id-validate nocheck
isakmp keepalive disable
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
authentication ms-chap-v2

But I cant connet ASA!

Everyone's tags (4)
1 REPLY
New Member

Re: How can I configure using win7 L2TP connect ASA 8.3(1)?

Can you send the debugs while you try to connect via L2TP...

#debug l2tp 255

#deb crypto isakmp 200

#deb crypto ipsec 200

Make sure you connect via mschap enabled username

user cisco pass cisco priv 0 mschapv2

Pradhuman Singh

828
Views
0
Helpful
1
Replies
CreatePlease to create content