Marvin
Thanks only problem is the edit does not go thru the same scrrens as the create screens so I deleted the existing easyvpn and created a second one. Only problem with that is the cisco remembers old info
here is my new config and I see some things that does not match the sample config from the article that richard pointed me out I highlighted them
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a privilege le
vel of 15.
Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.
username privilege 15 secret 0
no username cisco
Replace and with the username and password you want to use
.
For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
-----------------------------------------------------------------------
User Access Verification
Username: netman
Password:
MyRouter#sh cry isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id slot status
IPv6 Crypto ISAKMP SA
MyRouter#show run
Building configuration...
Current configuration : 7446 bytes
!
! Last configuration change at 09:27:39 EST Fri Dec 30 2011
! NVRAM config last updated at 09:27:39 EST Fri Dec 30 2011 by netman
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname MyRouter
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 xxxxxxxxxxxxxxxxxxxx/
!
aaa new-model
!
!
aaa group server radius sdm-vpn-server-group-1
server 192.168.69.15 auth-port 1645 acct-port 1646
!
aaa authentication login default local
aaa authentication login ciscocp_vpn_xauth_ml_1 group sdm-vpn-server-group-1 loc
al
aaa authentication login ciscocp_vpn_xauth_ml_2 local
aaa authorization exec default local
aaa authorization network ciscocp_vpn_group_ml_1 group sdm-vpn-server-group-1 lo
cal
aaa authorization network ciscocp_vpn_group_ml_2 local
!
aaa session-id common
!
resource policy
!
clock timezone EST -5
clock summer-time edt recurring
ip subnet-zero
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool sdm-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
!
!
ip cef
ip domain name TGCSNET.COM
ip name-server 71.242.0.12
ip name-server 71.250.0.12
ip name-server 4.2.2.2
!
!
crypto pki trustpoint TP-self-signed-1164042433
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1164042433
revocation-check none
rsakeypair TP-self-signed-1164042433
!
!
crypto pki certificate chain TP-self-signed-1164042433
certificate self-signed 01
3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31313634 30343234 3333301E 170D3032 30333031 30303038
34375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 31363430
34323433 3330819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B993 8AAE8B8C D8869842 C0C80A8C 57559B0A 243A306C EF726BD6 A79FBB30
63569C86 5117E6D9 9E14BF1D 2721D4C6 2CCFB67A D7A03AC3 6BC719DB 1237121C
8E310E9F 68F65DF7 B5986355 71B6C338 C34EC816 A677028D 0E131859 3A50E498
C1F94525 2DA35215 3EF10350 018C419A 4F49245F 1218C545 0BE18AA4 04A8F049
7AA90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
551D1104 18301682 144D7952 6F757465 722E5447 43534E45 542E434F 4D301F06
03551D23 04183016 80149A8A F1DA8EF9 7BC577ED 349FDA87 2E93A11F 8D16301D
0603551D 0E041604 149A8AF1 DA8EF97B C577ED34 9FDA872E 93A11F8D 16300D06
092A8648 86F70D01 01040500 03818100 3092C5D5 9FA063C7 E85E37A5 7F9B3AC3
A71B0BF1 A0BE1E4B 088C151A 6E056769 8E8FFCC9 3FA38091 38C53A49 CE1F20BE
172A1C93 282C5F97 19A6D3B0 CF65552D FEADA8C0 E89075DD 667B6ABE 9CF76D13
5E23D7CA A3BEC64D 21941DFB 3915D0C4 4221F663 1306DDF8 DF48E0AC DCC43028
0D392C9C 66EABDED BB4F4D54 5ED039B9
quit
username netman privilege 15 secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxx
username mynet privilege 15 secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxx
!
!
!
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp policy 2
group 2
!
crypto isakmp client configuration group TGCSVPN
key tgcsvpn01
dns 192.168.69.10 192.168.69.15
wins 192.168.69.10 192.168.69.15
domain our
pool SDM_POOL_1
netmask 255.255.255.0
crypto isakmp profile ciscocp-ike-profile-1
match identity group TGCSVPN
client authentication list ciscocp_vpn_xauth_ml_2
isakmp authorization list ciscocp_vpn_group_ml_2
client configuration address respond
virtual-template 2
!
!
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
!
crypto ipsec profile CiscoCP_Profile1
set security-association idle-time 86400
set transform-set ESP-3DES-SHA1
set isakmp-profile ciscocp-ike-profile-1
!
!
bridge irb
!
!
interface Loopback1
no ip address No ipaddress is this right?????????????????
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
description $ETH-WAN$
ip address 72.88.223.20 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
!
interface Virtual-Template2 type tunnel
ip unnumbered Loopback1
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
!
interface Dot11Radio0
no ip address
!
encryption vlan 1 mode ciphers tkip
!
ssid 010659120255
!
ssid TGCSNET
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 0 010659120255000000
!
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2437
station-role root
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no snmp trap link-status
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
no ip address
ip virtual-reassembly
ip tcp adjust-mss 1452
bridge-group 1
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 192.168.69.1 255.255.255.0
ip nat inside
ip virtual-reassembly
!
ip local pool SDM_POOL_1 192.168.70.75 192.168.70.99
ip classless
ip route 0.0.0.0 0.0.0.0 72.88.223.1 72.88.223.1 not valid ?????????????????
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 110 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.69.26 8080 interface FastEthernet4 8080
ip nat inside source static tcp 192.168.69.26 25 interface FastEthernet4 25
ip nat inside source static tcp 192.168.69.15 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.69.15 21 interface FastEthernet4 21
ip nat inside source static tcp 192.168.69.15 5900 interface FastEthernet4 5900
ip nat inside source static tcp 192.168.69.26 443 interface FastEthernet4 443
!
ip access-list extended denyDHCP
deny udp any any eq bootpc
deny udp any any eq bootps
permit ip any any
!
ip radius source-interface BVI1
access-list 23 permit 192.168.69.0 0.0.0.255
access-list 110 permit ip 192.168.69.0 0.0.0.255 any
no cdp run
radius-server host 192.168.69.15 auth-port 1645 acct-port 1646
!
control-plane
!
bridge 1 route ip
banner login ^C
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a privilege le
vel of 15.
Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.
username privilege 15 secret 0
no username cisco
Replace and with the username and password you want to use
.
For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
-----------------------------------------------------------------------
^C
!
line con 0
no modem enable
line aux 0
line vty 0 4
access-class 23 in
transport input telnet ssh
!
scheduler max-task-time 5000
ntp clock-period 17175144
ntp server 141.165.5.137
end
MyRouter#
Totally confuesed and lost here any ideas please help
Tom
