cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
641
Views
0
Helpful
3
Replies

Step how to configure ASA 5500 Series Security Services Module-10 ( Model: ASA-SSM-10 )

Sotheng Se
Level 1
Level 1

Dear Support,

I need to configure Security Services Module-10 ( Model: ASA-SSM-10 ) on my ASA firewall 5510. Could you provide configuration step and how to connect to module?

Below is it's information on module

ciscoasa(config)# sh module 1 details
Getting details from the Service Module, please wait...
ASA 5500 Series Security Services Module-10
Model:              ASA-SSM-10
Hardware version:   1.0
Serial Number:      JAF1115066U
Firmware version:   1.0(11)2
Software version:   6.0(1)E1
MAC Address Range:  001a.e268.5aa9 to 001a.e268.5aa9
App. name:          IPS
App. Status:        Up
App. Status Desc:   
App. version:       6.0(1)E1
Data plane Status:  Up
Status:             Up
Mgmt IP addr:       133.1.9.144                                                 
Mgmt web ports:     443                                                         
Mgmt TLS enabled:   true   

your help is very appreciate.

thank you,

 

Best Regards,

 

2 Accepted Solutions

Accepted Solutions

nkarthikeyan
Level 7
Level 7

Hi Sothengse,

Please find the samlpe configurations on AIP SSM module. You can go through this to start with.

http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/71204-traffic-asa-aip-ssm.html

https://www.youtube.com/watch?v=FgYU5ZXwk4g

 

Regards

Karthik

 

View solution in original post

nkarthikeyan
Level 7
Level 7

Hi Sothengse,

 

For initial login to the device follow the below mentioned steps....

 

Logging In to AIP SSM

You can log in to the AIP SSM from ASA 5500 series adaptive security appliance.


Note You must initialize the AIP SSM (run the setup command) from ASA 5500 series adaptive security appliance. After networking is configured, SSH and Telnet are available.


To session in to the AIP SSM from ASA 5500 series adaptive security appliance, follow these steps:


Step 1 Log in to ASA 5500 series adaptive security appliance.


Note If ASA 5500 series adaptive security appliance is operating in multi-mode, use the change system command to get to the system level prompt before continuing.


Step 2 Session to the AIP SSM:

asa# session 1

Opening command session with slot 1.

Connected to slot 1. Escape character sequence is 'CTRL-^X'.


 

You have 60 seconds to log in before the session times out.

Step 3 Enter your username and password at the login prompt:


Note The default username and password are both cisco. You are prompted to change them the first time you log in to the AIP SSM. You must first enter the UNIX password, which is cisco. Then you must enter the new password twice.


login: cisco

Password: 

***NOTICE***

This product contains cryptographic features and is subject to United States

and local country laws governing import, export, transfer and use. Delivery

of Cisco cryptographic products does not imply third-party authority to import,

export, distribute or use encryption. Importers, exporters, distributors and

users are responsible for compliance with U.S. and local country laws. By using

this product you agree to comply with applicable laws and regulations. If you

are unable to comply with U.S. and local laws, return this product immediately.


 

A summary of U.S. laws governing Cisco cryptographic products may be found at:


 

If you require further assistance please contact us by sending email to

export@cisco.com.


 

***LICENSE NOTICE***

There is no license key installed on the system.

to obtain a new license or install a license.

aip-ssm#

 

Regards

Karthik

View solution in original post

3 Replies 3

nkarthikeyan
Level 7
Level 7

Hi Sothengse,

Please find the samlpe configurations on AIP SSM module. You can go through this to start with.

http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/71204-traffic-asa-aip-ssm.html

https://www.youtube.com/watch?v=FgYU5ZXwk4g

 

Regards

Karthik

 

 

Dear nkarthikeyan,

Your above configuration step is working for me. Thank you so much for your quick respond, useful help and correct answer.

 

Best Regards,

thanks

 

nkarthikeyan
Level 7
Level 7

Hi Sothengse,

 

For initial login to the device follow the below mentioned steps....

 

Logging In to AIP SSM

You can log in to the AIP SSM from ASA 5500 series adaptive security appliance.


Note You must initialize the AIP SSM (run the setup command) from ASA 5500 series adaptive security appliance. After networking is configured, SSH and Telnet are available.


To session in to the AIP SSM from ASA 5500 series adaptive security appliance, follow these steps:


Step 1 Log in to ASA 5500 series adaptive security appliance.


Note If ASA 5500 series adaptive security appliance is operating in multi-mode, use the change system command to get to the system level prompt before continuing.


Step 2 Session to the AIP SSM:

asa# session 1

Opening command session with slot 1.

Connected to slot 1. Escape character sequence is 'CTRL-^X'.


 

You have 60 seconds to log in before the session times out.

Step 3 Enter your username and password at the login prompt:


Note The default username and password are both cisco. You are prompted to change them the first time you log in to the AIP SSM. You must first enter the UNIX password, which is cisco. Then you must enter the new password twice.


login: cisco

Password: 

***NOTICE***

This product contains cryptographic features and is subject to United States

and local country laws governing import, export, transfer and use. Delivery

of Cisco cryptographic products does not imply third-party authority to import,

export, distribute or use encryption. Importers, exporters, distributors and

users are responsible for compliance with U.S. and local country laws. By using

this product you agree to comply with applicable laws and regulations. If you

are unable to comply with U.S. and local laws, return this product immediately.


 

A summary of U.S. laws governing Cisco cryptographic products may be found at:


 

If you require further assistance please contact us by sending email to

export@cisco.com.


 

***LICENSE NOTICE***

There is no license key installed on the system.

to obtain a new license or install a license.

aip-ssm#

 

Regards

Karthik

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: