Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

VPN with GNS3

Hi All,


I just want to know Why I m not able open router in webpage with SDM client software.


Just find the attach file here..



My router IP add : 192.168.10.1/24 ( Fa 0/0 ) n cloud is connected to my loop back interface with 192.168.10.50/24


I m albe to ping my loop back as well as Router IP address.


but when I tring to open my router in webpage through SDM in IE,Firefox ,or google crome ..it's showing waitng / loading ......loading ...


Can u tell me where I did mistake ???


I configured router with CMD's:

---

ip http server

username cisco pass cisco

-------

In SDM  client software :

----

Device ID orh hostname : 192.168.10.1 - connect.. showing loading ....loading...


tried on all K9 IOS :

----

c3640-jk9o3s-mz.123-14.T7.extracted

c7200-jk9o3s-mz.124-19

c2600-adventerprisek9-mz.124-21


Could any one please help me regarding this issue...?


Thank in advance,


Thanks,

Rajdeep P



Thanks & regards, Rajdeep Parmar
4 REPLIES
New Member

Re: VPN with GNS3

Hi,

   I was able to use SDM and ASDM with GNS3. I used IE and not firefox.

You have to enable http on the router and connect with SDM.

If it's not working, try to connect with IE.

New Member

Re: VPN with GNS3

Hi.


Thanks for your reply....


As I mentioned I was not able open by using IE v8....


Could you please tell me which IOS you used for SDM...???


Means Entire - IOS Name ...


Thanks,

Rajdeep P.

Thanks & regards, Rajdeep Parmar
New Member

Re: VPN with GNS3

Hi,

   I used SDM, last year.

I will try to test it this week and reply this topic.

New Member

Re: VPN with GNS3

Hi,

   I have tested and it's working fine for me. I am using bridged connection between the cloud and the f0/0 of the router in GNS3. The interface works on internet explorer.

Here is the config and ios ver.

Router#sh ver
Cisco IOS Software, 3600 Software (C3640-A3JS-M), Version 12.4(25c), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 12-Feb-10 00:48 by prod_rel_team

ROM: ROMMON Emulation Microcode
ROM: 3600 Software (C3640-A3JS-M), Version 12.4(25c), RELEASE SOFTWARE (fc2)

Router uptime is 13 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"

Cisco 3640 (R4700) processor (revision 0xFF) with 124928K/6144K bytes of memory.
Processor board ID 00000000
R4700 CPU at 100MHz, Implementation 33, Rev 1.2
1 FastEthernet interface
DRAM configuration is 64 bits wide with parity enabled.
125K bytes of NVRAM.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Router#sh run
Building configuration...

Current configuration : 591 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
memory-size iomem 5
!
ip cef
!
username dorin privilege 15 secret 5 $1$q2K6$bRFAKeal.T/4lyawyOouC.
!
interface FastEthernet0/0
ip address 192.168.2.150 255.255.255.0
duplex auto
speed auto
!

ip http server
ip http authentication local
ip forward-protocol nd
!
control-plane
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

2218
Views
0
Helpful
4
Replies