Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

1760 with vic 4fxs/did card

I have a 1760 router that have two wic cards on slot 0 and 1. And 2 vic 4fxs/did cards on slot 2 and 3.

Problem is that the two vic4fxs/did cards, don't show up on hardware list, there is a green light on the slot 2 and 3 that is OK, the 4 ports on each card are amber, but the router doesn't reconize the card.

Is ther any comand that I have to do to enable the card on the slot, for fxs?

Regards

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Super Gold

Re: 1760 with vic 4fxs/did card

Most likely you're missing the necessary DSP module to support the voice interface.

Do "show diag" to see what do you have in the router.

For example, a PVDM-256K-8 would be enough for 8 analog voice ports, but not for additional ones.

Hope this helps, please rate post if it does!

4 REPLIES
Highlighted
Hall of Fame Super Gold

Re: 1760 with vic 4fxs/did card

Most likely you're missing the necessary DSP module to support the voice interface.

Do "show diag" to see what do you have in the router.

For example, a PVDM-256K-8 would be enough for 8 analog voice ports, but not for additional ones.

Hope this helps, please rate post if it does!

Community Member

Re: 1760 with vic 4fxs/did card

Slot 0:

C1760 1FE VE 4SLOT DV Mainboard Port adapter, 12 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 6.0

PCB Serial Number : FOC091716SP

Part Number : 73-7167-06

Board Revision : A0

Fab Version : 04

Product (FRU) Number : CISCO1760

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 16 41 06 00 C1 8B 46 4F 43 30 39 31

0x10: 37 31 36 53 50 82 49 1B FF 06 42 41 30 02 04 FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Packet Voice DSP Module Slot 0:

Not populated

Packet Voice DSP Module Slot 1:

Not populated

WIC/VIC Slot 0:

Serial 1T

Hardware revision 1.0 Board revision J0

Serial number 0028151857 Part number 800-01514-01

FRU Part Number WIC-1T=

Test history 0x00 RMA number 00-00-00

Connector type WAN Module

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 02 01 00 01 AD 90 31 50 05 EA 01 00 00 00 00

0x30: 98 00 00 00 11 11 02 01 FF FF FF FF FF FF FF FF

WIC/VIC Slot 1:

Serial 2T (12in1)

Hardware revision 1.0 Board revision B0

Serial number 0031961241 Part number 800-03181-02

FRU Part Number WIC-2T=

Test history 0x00 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 12 01 00 01 E7 B0 99 50 0C 6D 02 00 00 00 00

0x30: 58 00 00 00 04 03 26 00 FF FF FF FF FF FF FF FF

VIC Slot 2:

Quad FXS DID Voice Interface Card

Daughter card-Version 4 TLV Cookie Format

Hardware Revision : 3.1

Part Number : 73-6918-02

Board Revision : E0

Deviation Number : 0

Fab Version : 02

PCB Serial Number : FOC11131MR4

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Top Assy. Part Number : 800-17016-02

Connector Type : 01

Product (FRU) Number :

VIC Slot 3:

Quad FXS DID Voice Interface Card

Daughter card-Version 4 TLV Cookie Format

Hardware Revision : 3.1

Part Number : 73-6918-02

Board Revision : E0

Deviation Number : 0

Fab Version : 02

PCB Serial Number : FOC11131MSQ

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Top Assy. Part Number : 800-17016-02

Connector Type : 01

Product (FRU) Number :

Hall of Fame Super Gold

Re: 1760 with vic 4fxs/did card

So you need a minimum of PVDM-256K-8.

Thanks for the appreciation and good luck!

Community Member

Re: 1760 with vic 4fxs/did card

Thanks for the support

200
Views
5
Helpful
4
Replies
CreatePlease to create content