Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

1861 switchport port-security command

Dear All,

I just need to confirm that either 1861 CME routers support switchport port-security .... commands are available???

If yes then on which IOS and if not then what is the alternate to fix the port security on the 8-port ethernet card?

thanks,

14 REPLIES
Hall of Fame Super Gold

Re: 1861 switchport port-security command

3-port ethernet card???   I've never heard of one.  Can you provide the model number of this card?

New Member

Re: 1861 switchport port-security command

sorry. typo mistake,,, it is 8-port ethernet card !!!

thanks

Hall of Fame Super Gold

Re: 1861 switchport port-security command

8-port switch on an 1800 ISR G1?  You mean the NME-XD-48ES-2S-P?

IF so, then it won't work because this is supported starting from the 2800 router.

Cisco EtherSwitch Service Modules for Cisco Integrated Services Routers
http://www.cisco.com/en/US/prod/collateral/routers/ps5855/product_data_sheet0900aecd8028d15f.html

New Member

Re: 1861 switchport port-security command

then please tell me how I can configure switchport security on 1861 ethernet port???

Hall of Fame Super Gold

Re: 1861 switchport port-security command

If indeed you are using the module, it's not the question of you can or can't configure.  It's a question of whether or not the module is even supported on the 1800 router.

New Member

Re: 1861 switchport port-security command

The 8-port ethernet module is supported in 1861 routers.

Hall of Fame Super Gold

Re: 1861 switchport port-security command

What is the complete model number of the module?

New Member

Re: 1861 switchport port-security command

Dear Friend,

The module is built-in / fix in the 1861 router.

Ref: http://www.cisco.com/en/US/products/ps8321/index.html

Thanks,

Aman

Hall of Fame Super Gold

Re: 1861 switchport port-security command

Oh nuts.  I forgot about this model. 

Port security should be supported.  Can you post your config and what you are trying to do?

New Member

Re: 1861 switchport port-security command

Dear Friend,

I am trying to put the command in the interface mode...

switchport port-security .....

but this command is not available in this router.... do I need to configure it some other way or need ot upgarde the IOS... If the IOS then which IOS???

Thanks,

Aman

Hall of Fame Super Gold

Re: 1861 switchport port-security command

Are you entering the command on the LAN ports or the WAN ports?

New Member

Re: 1861 switchport port-security command

Friend,

I am configuring switchport security on the LAN interfaces, IP phones are terminating on these ports directly......

New Member

Re: 1861 switchport port-security command

Hi,

Would you please share the output of sh ver

Shailesh

New Member

Re: 1861 switchport port-security command

Here is how it is configured,

It will not shut down the port, but prevents traffic other than what is specified from passing:

mac-address-table secure 0007.0002.0006 FastEthernet0/1/1 vlan 7

658
Views
0
Helpful
14
Replies
CreatePlease to create content