I'm having issues with a 1921 and a new 4G card.
Below is the running config, show cellular and debug. The SP is EE in the UK, the APN is supposed to be everywhere, eesecure is the user and the password is also set (although not shown). The SP has confirmed the SIM is fine and the profile is correct. Apart from that they are not willing to help.
Can't see what is wrong here, any ideas? Anything else I can check?
Thanks
Chris
Router#sh cellular 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.19.04
Modem Firmware built = 2012/09/17 17:57:14
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = 23404100839842
International Mobile Equipment Identity (IMEI) = 359470040067474
Integrated Circuit Card ID (ICCID) = 8944302751624005845
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) = 07947586729
Profile Information
====================
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = everywhere
Authentication = Unknown
Username: eesecure
Password:
* - Default profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Mobile Country Code (MCC) = 234
Mobile Network Code (MNC) = 30
Packet switch domain(PS) state = Attached
Registration(EMM) state = Registered
Radio Information
=================
Radio power mode = ON
Current RSSI = -75 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
Error Information
=================
This command is not supported on 4G modems.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Router#
Router#sh run
Building configuration...
Current configuration : 1787 bytes
!
! Last configuration change at 10:33:53 UTC Fri Nov 1 2013
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
enable secret 4 eaOP83n/Avy2EAs2tg7JbhLCX5T8h39E3GwBeTDW5sY
!
no aaa new-model
!
ip cef
!
no ipv6 cef
!
multilink bundle-name authenticated
!
chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
!
controller Cellular 0/0
!
!
interface Loopback0
ip address 192.168.1.1 255.255.255.0
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
ip address 10.10.10.10 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Cellular0/0/0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 60
dialer string lte
dialer-group 1
async mode interactive
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat inside source list 101 interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0/0/0
!
access-list 101 permit ip 10.10.10.0 0.0.0.255 any
dialer-list 1 protocol ip permit
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 0/0/0
script dialer lte
modem InOut
no exec
transport input all
transport output all
rxspeed 100000000
txspeed 50000000
line vty 0 4
login
transport input all
!
scheduler allocate 20000 1000
!
end
Router#
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
*Nov 1 10:47:18.059: Ce0/0/0 DDR: place call
*Nov 1 10:47:18.059: Ce0/0/0 DDR: Dialing cause ip (s=192.168.1.1, d=8.8.8.8)
*Nov 1 10:47:18.059: Ce0/0/0 DDR: Attempting to dial lte
*Nov 1 10:47:18.059: CHAT0/0/0: Attempting async line dialer script
*Nov 1 10:47:18.059: CHAT0/0/0: Dialing using Modem script: lte & System script: none
*Nov 1 10:47:18.059: CHAT0/0/0: process started
*Nov 1 10:47:18.059: CHAT0/0/0: Asserting DTR
*Nov 1 10:47:18.059: CHAT0/0/0: Chat script lte started
*Nov 1 1.0:47:18.059: CHAT0/0/0: Sending string: AT!CALL
*Nov 1 10:47:18.059: CHAT0/0/0: Expecting string: OK....
Success rate is 0 percent (0/5)
Router#
*Nov 1 10:48:18.059: CHAT0/0/0: Timeout expecting: OK
*Nov 1 10:48:18.059: CHAT0/0/0: Chat script lte finished, status = Connection timed out; remote host not responding
*Nov 1 10:48:18.059: Ce0/0/0 DDR: disconnecting call
*Nov 1 10:48:33.059: Ce0/0/0 DDR: re-enable timeout
Router#
Router#
Router#
