Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

2600 Router - Receive Errors

My company uses NetFlow software to find issues with our network. The software indicated we have thousands of "Receive Errors" each day with our Ethernet 0/0 interface. Does anyone know what may be causing these errors and what steps I can take to prevent these error?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: 2600 Router - Receive Errors

Hi, please configure 100 mbps and full duplex on the switch port also.

This should eliminate the errors that surely are somewhat slowing down traffic.

As a recognition to those providing answers, please rate useful posts with the scrollbox below!

6 REPLIES
Hall of Fame Super Gold

Re: 2600 Router - Receive Errors

Please check "show interface eth0/0" and if in doubt post output here.

New Member

Re: 2600 Router - Receive Errors

The output of Show interface fastEthernet 0/0 is as follows:

show interface fastEthernet 0/0

FastEthernet0/0 is up, line protocol is up

Hardware is AmdFE, address is 000e.833e.2200 (bia 000e.833e.2200)

Internet address is 10.10.1.6/24

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s, 100BaseTX/FX

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 1/75/1705/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 193000 bits/sec, 179 packets/sec

5 minute output rate 192000 bits/sec, 176 packets/sec

1181645207 packets input, 2438941583 bytes

Received 47201389 broadcasts, 0 runts, 0 giants, 0 throttles

4429681 input errors, 4429681 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

1129333917 packets output, 2498682094 bytes, 0 underruns

0 output errors, 0 collisions, 4 interface resets

0 babbles, 0 late collision, 0 deferred

122 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Hall of Fame Super Gold

Re: 2600 Router - Receive Errors

You monitoring tool is correct, there are too many errors for a normal ethernet link.

Check cabling and work with the manager of the connected device to have the issue resolved.

New Member

Re: 2600 Router - Receive Errors

I have a Cisco 3560G switch that is connected to that FastEthernet port. I swapped out the cable that connects the router to the switch - still giving errors. The port on the switch that the router is plugged into is indicating that it is running at half duplex. Is this normal?

Also, Would these errors cause a great slow down on our network? All of the PCs in my company points to this router as their gateway.

Hall of Fame Super Gold

Re: 2600 Router - Receive Errors

Hi, please configure 100 mbps and full duplex on the switch port also.

This should eliminate the errors that surely are somewhat slowing down traffic.

As a recognition to those providing answers, please rate useful posts with the scrollbox below!

New Member

Re: 2600 Router - Receive Errors

Thank you very much, this worked.

903
Views
0
Helpful
6
Replies