Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

2651 router upgrade failure - not enough space

I have c2600-i-mz.123-26.bin running.  If I attempt to upgrade to it IP Plus version I get the following:

Erasing device... eeeeeeeee  ...NOT erased

Erase of flash: complete

loading c2600-is-mz.123-26.bin: !!!!!!

%Error copying flash:c2600-is-mz.123-26.bin (No space left on device)

The requirement for this IOS is 32MB, which I have, but it doesn't seem to work properly.

I tried to squeeze the flash, but get the following:

First create squeeze log by erasing the entire device  -NOT SURE HOW TO DO THIS WITH A PRODUCTION ROUTER-

%Error squeezing flash (Missing or corrupted log)

Is the memory bad?  Why the NOT erased message?

Any assistance would be appreciated!

Version Information:

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(26), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 17-Mar-08 15:23 by dchih

ROM: System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)

Router uptime is 2 hours, 55 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.123-26.bin"

cisco 2651 (MPC860P) processor (revision 0x200) with 126976K/4096K bytes of memory.
Processor board ID JAB05160ASL (2887752866)
M860 processor: part number 5, mask 1
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

14 REPLIES
Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

Try format flash:

New Member

Re: 2651 router upgrade failure - not enough space

To be on the safe side, you might want to back up your configs before you decide to format. Most important rule to be followed with Networking devices.

Stonet72

Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

To be on the safe side, you might want to back up your configs before  you decide to format. Most important rule to be followed with Networking  devices.

Cisco does not store config on flash.

Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

Squeeze flash:

Re: 2651 router upgrade failure - not enough space

Flash might be faulty.

Try formatting the flash card and if it gives you error, then try to remove and reinsert it (flash card are hot swappable).

After you have re-inserted flash card, again try to format it. If it still gives you error; probably flash card might be faulty.

And if it doesn't gives you error, VOILA.. u got your flash clean. Time to upgrade it with the new IOS.

Regards,

Smitesh

Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

Try formatting the flash card and if it gives you error, then try to  remove and reinsert it (flash card are hot swappable).

Incorrect, 2600 routers except 2691, have internal flash module, not CF.

New Member

Re: 2651 router upgrade failure - not enough space

Thanks for all the response!

Squeeze flash results in the following error: %Error squeezing flash (Missing or corrupted log)

Format flash is invalid on this device.

Erase flash produces the NOT ERASED message.

The flash is internal on this unit.  I'm assuming it's not hot swapable.

Thoughts?

Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

Open router and replace flash.

Or replace entire router that is very old anyway.

New Member

Re: 2651 router upgrade failure - not enough space

Sugegst you try loading the image from xmodem(console). this will automatically erase the flash and load image but your router would be down atleast for an hour at a speed of 115200.

Regards,

Bhavesh

Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

To the person that rated me an 1:

Explain exactly if you can, where I'm wrong?

New Member

Re: 2651 router upgrade failure - not enough space

Hi,

  1. check flash space with command 'Router#show flash' http://www.cisco.com/en/US/products/sw/iosswrel/ps1834/products_tech_note09186a00800fb9d9.shtml
  2. Follow steps Refer http://www.ciscopros.info/en/US/docs/ios/12_2/configfun/configuration/guide/fcf006_ps1835_TSD_Products_Configuration_Guide_Chapter.html
    • Delete unwanted files in flash partition -- delete command
    • Erase files from Flash Partition - Erase command
    • Format - to complete cleanup the flash data

This will help you to check how many flash partitions you have, are there any unwanted files in the flash dir and facilitate for clearing the space.

Hope this will make you happy to progress

Shailesh

New Member

Re: 2651 router upgrade failure - not enough space

I'm not sure who rated your post, but it wasn't me...  It's actually quite helpful.

Hall of Fame Super Gold

Re: 2651 router upgrade failure - not enough space

My apologies then; I've edited my post accordingly.

New Member

Re: 2651 router upgrade failure - not enough space

I'm assuming the flash is bad.  I've ordered a replacement module to try.  I'd rather not replace a router that is 100% reliable.

1474
Views
1
Helpful
14
Replies
CreatePlease to create content