Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

2821 card command problem

Hi,

I have installed am ATM module in a 2821 router, but I have no chance to put the command 'mode atm aim 1'

murotuer(config)#controller E1 0/3/0

myrouter(config-controller)#mode ?

  cas  Configure CAS (Channel Associated Signal) mode

  ccs  Configure CCS (Common Channel Signal) mode

myrouter#sh diag

AIM Module in slot: 1

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-27059-01

        Board Revision           : A0

WIC Slot 3:

        E1 (2 port) Multi-Flex Trunk WAN daughter card

        Hardware revision 1.0           Board revision A0

        Serial number     36554718      Part number    800-04479-05

        Version Identifier     V02      FRU Part Number     VWIC-2MFT-E1  

IOS: flash:c2800nm-advipservicesk9-mz.124-24.T4.bin

I have tried in both ATM ports but nothing changed.

Any idea why I dont' have the mode ATM command?

Regards and thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Green

2821 card command problem

Hi,

Sorry that was bad use of copy & paste by me.

I should have pasted this :-

NAME: "Virtual Private Network (VPN) Module on Slot 1", DESCR: "Encryption AIM Element"
PID: AIM-VPN/SSL-2     , VID: V01, SN: FO

This is for VPNs and SSL

As I said this is the wrong type of AIM for ATM support

You need the AIM-ATM variant

Regards

Alex

Regards, Alex. Please rate useful posts.
5 REPLIES
Green

2821 card command problem

Hi,

I think you may have the wrong kind of AIM card

Can you post show inven

Regards

Alex

Regards, Alex. Please rate useful posts.
New Member

2821 card command problem

myrouter#sh inv
NAME: "2821 chassis", DESCR: "2821 chassis"
PID: CISCO2821         , VID: V03 , SN: FTXxxx

NAME: "2nd generation two port FXS voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "2nd generation two port FXS voice interface daughtercard"
PID: VIC2-2FXS         , VID: V01 , SN: FOCxxx

NAME: "2nd generation two port FXS voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation two port FXS voice interface daughtercard"
PID: VIC2-2FXS         , VID: V01 , SN: FOCxxx

NAME: "2nd generation two port FXS voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation two port FXS voice interface daughtercard"
PID: VIC2-2FXS=        , VID: V  , SN: FOCxxx

NAME: "Two port E1 voice interface daughtercard on Slot 0 SubSlot 3", DESCR: "Two port E1 voice interface daughtercard"
PID: VWIC-2MFT-E1      , VID: V02, SN: xx  

NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with Two DSPs"
PID: PVDM2-32          , VID: V01 , SN: FOCx

NAME: "Virtual Private Network (VPN) Module on Slot 1", DESCR: "Encryption AIM Element"
PID: AIM-VPN/SSL-2     , VID: V01, SN: FO

NAME: "8-port Analog Modem Card Version 2 on Slot 1", DESCR: "8-port Analog Modem Card Version 2"
PID:                   , VID: 1.0, SN: F

Green

2821 card command problem

Hi,

This is your issue.

PID: AIM-VPN/SSL-2     , VID: V01, SN: FO

NAME: "8-port Analog Modem Card Version 2 on Slot 1", DESCR: "8-port Analog Modem Card Version 2"
PID:                   , VID: 1.0, SN: F

This is NOT for ATM support.

You need

AIM-ATM variant

Regards

Alex

Regards, Alex. Please rate useful posts.
New Member

2821 card command problem

Sorry, but I don't understand 'NAME: "8-port Analog Modem Card Version 2 on Slot 1", DESCR: "8-port Analog Modem Card Version' is for dial up access.

I need to configure the ATM for the VWIC-2MFT-E1 card.

Regards and thanks

Green

2821 card command problem

Hi,

Sorry that was bad use of copy & paste by me.

I should have pasted this :-

NAME: "Virtual Private Network (VPN) Module on Slot 1", DESCR: "Encryption AIM Element"
PID: AIM-VPN/SSL-2     , VID: V01, SN: FO

This is for VPNs and SSL

As I said this is the wrong type of AIM for ATM support

You need the AIM-ATM variant

Regards

Alex

Regards, Alex. Please rate useful posts.
453
Views
0
Helpful
5
Replies
CreatePlease to create content