Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

2851 and 48 Port EtherSwitch Module issue

router# copy flash: xmodem

Ok guys the above command is not working at all it should have coppied the image to the etherswitch module but it just renames the file and copy it in the router flash im pasting both the outputs.

It should work like that:

Router# copy flash: xmodem

**** WARNING ****

x/ymodem is a slow transfer protocol limited to the current speed

settings of the auxiliary/console ports. The use of the auxiliary

port for this download is strongly recommended.

During the course of the download no exec input/output will be

available.

---- ******* ----

Proceed? [confirm]

You are prompted for the source filename and destination filename:

Source filename [loader_bs.img]?

Destination filename [loader_bs.img]?

You are prompted for the Cisco EtherSwitch service module slot number:

Service Module slot number? [1]:

Step 8 dir flash:

Example:

switch> dir flash:

Displays a list of all files and directories in flash memory on

the service module.

Step 9 boot flash: image

Example:

switch> boot flash:c3825-i5-mz.050404

Boots the Cisco EtherSwitch service module image if all

files and directories are in flash memory on the service

module.

Command or Action Purpose

Cisco EtherSwitch Service Modules Feature Guide

Troubleshooting the Cisco EtherSwitch Service Module Software

70

Cisco IOS Release 12.2(25)SEC

You are prompted for the service module interface number. Accept the default:

Service Module interface number? [0]:

You are prompted to confirm the buffer. Accept the default:

1k buffer? [confirm]

You are prompted for the max retry count. Accept the default:

Max Retry Count [10]:

You are prompted to confirm the transfer to the Cisco EtherSwitch service module:

Xmodem send on slot 2 interface 0. Please be sure there is enough space on receiving side.

Continue? [confirm]

The following appears when the image is downloaded to the service module:

Ready to send

file...........C!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!

262144 bytes copied in 101.744 secs (2577 bytes/sec)

--------------------------------------------------------------

And this is whats happening with me.

yourname#copy flash: xmodem

Source filename [c3750-ipservicesk9-mz.122-35.SE5.bin]?

Destination filename [xmodem]?

%Warning:There is a file already existing with this name

Do you want to over write? [confirm]

Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

8638247 bytes copied in 21.604 secs (399845 bytes/sec)

and #Show flash:

14 8638247 Feb 28 2009 08:39:40 +00:00 c3750-ipservicesk9-mz.122-35.SE5.bin

15 8638247 Feb 28 2009 10:05:04 +00:00 xmodem

---------------------------------------------------------------

6 REPLIES

Re: 2851 and 48 Port EtherSwitch Module issue

Why are u trying to do xmodem, is the software corrupted?

All you need to do is copy the software on to the routers flash and set the boot parameters

eg.

router#copy tftp: flash:

Then use

service-module interface slot/port session

boot flash: image

HTH

Narayan

New Member

Re: 2851 and 48 Port EtherSwitch Module issue

Yeh the IOS on the etherswitch is corrupted, and every time i take session it takes me to the ROMMON.

Re: 2851 and 48 Port EtherSwitch Module issue

copy tftp: xmodem

Source filename [c3750-ipservicesk9-mz.122-35.SE5.bin]?

Destination filename [xmodem]?

You are actually renaming the file to xmodem

The flash shows that it has a 3750 image so just go into the service module and try to boot

http://www.cisco.com/en/US/docs/ios/12_3t/12_3t14/feature/guide/miragenm.html#wp1768057

Narayan

Hall of Fame Super Gold

Re: 2851 and 48 Port EtherSwitch Module issue

The command you are trying to use (copy flash: xmodem) tells the appliance to copy A file from flash and NAME it as "xmodem".

New Member

Re: 2851 and 48 Port EtherSwitch Module issue

Yeh i know that, but if you refer the guide it should ask me about the location of ether switch but it isn't.

New Member

Re: 2851 and 48 Port EtherSwitch Module issue

>><<

567
Views
0
Helpful
6
Replies