Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

2950 error message

please i need urgent solution to the log below.i need to access the switch.ports not blinking at all but fan on.what do i do

C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)

Compiled Mon 22-Jul-02 17:18 by antonino

WS-C2950-24 starting...

Base ethernet MAC Address: 00:17:5a:1c:77:40

Xmodem file system is available.

Initializing Flash...

flashfs[0]: 373 files, 4 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 7741440

flashfs[0]: Bytes used: 4752384

flashfs[0]: Bytes available: 2989056

flashfs[0]: flashfs fsck took 7 seconds.

...done initializing flash.

Boot Sector Filesystem (bs:) installed, fsid: 3

Parameter Block Filesystem (pb:) installed, fsid: 4

Loading "flash:/c2950-i6q4l2-mz.121-22.EA6.bin"...#############################################################################################################################################################################################################

File "flash:/c2950-i6q4l2-mz.121-22.EA6.bin" uncompressed and installed, entry point: 0x80010000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Fri 21-Oct-05 01:59 by yenanh

Image text-base: 0x80010000, data-base: 0x80568000

Initializing flashfs...

flashfs[1]: 373 files, 4 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 7741440

flashfs[1]: Bytes used: 4752384

flashfs[1]: Bytes available: 2989056

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

Done initializing flashfs.

POST: System Board Test : Passed

POST: Ethernet Controller Test : Passed

ASIC Initialization Passed

%Error: initializing transceiver port Fa0/1

%Error: initializing transceiver port Fa0/2

%Error: initializing transceiver port Fa0/3

%Error: initializing transceiver port Fa0/4

%Error: initializing transceiver port Fa0/5

%Error: initializing transceiver port Fa0/6

%Error: initializing transceiver port Fa0/7

%Error: initializing transceiver port Fa0/8

%Error: initializing transceiver port Fa0/9

%Error: initializing transceiver port Fa0/10

%Error: initializing transceiver port Fa0/11

%Error: initializing transceiver port Fa0/12

%Error: initializing transceiver port Fa0/13

%Error: initializing transceiver port Fa0/14

%Error: initializing transceiver port Fa0/15

%Error: initializing transceiver port Fa0/16

%Error: initializing transceiver port Fa0/17

%Error: initializing transceiver port Fa0/18

%Error: initializing transceiver port Fa0/19

%Error: initializing transceiver port Fa0/20

%Error: initializing transceiver port Fa0/21

%Error: initializing transceiver port Fa0/22

%Error: initializing transceiver port Fa0/23

%Error: initializing transceiver port Fa0/24

2 REPLIES
Hall of Fame Super Silver

Re: 2950 error message

hello Olakunle,

first of all using an attachment file would have been a better choice.

I'm afraid to give you bad news: it looks like the switch is not able to access the ports.

Try to power off. Let it powered off for some time.

Then try again.

If still it suffers of the same problem if you have a valid contract for it ask for a replacement unit.

Hope to help

Giuseppe

Hall of Fame Super Gold

Re: 2950 error message

Please try to avoid cross-posting. One post is sufficient.

317
Views
0
Helpful
2
Replies
CreatePlease to create content