Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with ATM

Product#: VWIC2-2MFT-T1/E1

Can use this with ATM connection.

i cannot use the command "mode atm aim 0"

thanks

Wael

2 ACCEPTED SOLUTIONS

Accepted Solutions
New Member

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Hi,

If you can see below output from "sh ver". Which mean you have correct AIM-ATM module installed. Else pls make sure you purchase it and install properly.

Processor board ID FHK1116F3CN

2 Gigabit Ethernet interfaces

1 ATM interface

2 Channelized E1/PRI ports

1 Virtual Private Network (VPN) Module

1 ATM/Voice AIM

Also, if you can see it. Please add "mode atm aim 0" under controller e1 0/0/0

controller E1 0/0/0

mode atm aim 0

Hope it help.

Thanks.

Rgds,

Christopher

Hall of Fame Super Gold

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Hi, to add to the good advice from Chris, I will try be even more clear:

You need to buy a piece of hardware called AIM-ATM, open the router, and fit it inside.

Without it, you cannot do ATM and the commands are not recognized.

As a recognition to those giving answers, please rate useful posts with the scrollbox below!

8 REPLIES
Hall of Fame Super Gold

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Do you have the AIM-ATM installed? Do "show diag" to check.

Hope this helps, please rate post if it does!

New Member

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

how to install that i am using Cisco Router 1841

Hall of Fame Super Gold

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Open the router and fit the module inside.

Hope this helps, please rate post if it does!

New Member

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

i already did that but i cannot make it work on ATM.

i cannot issue the commands.

my question is does this module supports ATM connection.?

New Member

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Hi,

If you can see below output from "sh ver". Which mean you have correct AIM-ATM module installed. Else pls make sure you purchase it and install properly.

Processor board ID FHK1116F3CN

2 Gigabit Ethernet interfaces

1 ATM interface

2 Channelized E1/PRI ports

1 Virtual Private Network (VPN) Module

1 ATM/Voice AIM

Also, if you can see it. Please add "mode atm aim 0" under controller e1 0/0/0

controller E1 0/0/0

mode atm aim 0

Hope it help.

Thanks.

Rgds,

Christopher

Hall of Fame Super Gold

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Hi, to add to the good advice from Chris, I will try be even more clear:

You need to buy a piece of hardware called AIM-ATM, open the router, and fit it inside.

Without it, you cannot do ATM and the commands are not recognized.

As a recognition to those giving answers, please rate useful posts with the scrollbox below!

New Member

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Thanks Bevilacqua and chris. That was my question The card that mentioned in the topic cannot act as ATM module.

i will buy ATM Module and try it.

i tried to do this it worked but i cannot add the command "mode atm aim 0" only "mode atm" without "aim 0"

card type e1 0/0/0:0

controller E1 0/0/0

mode atm

anyways thanks it seems this card is not compatible i will get ATM-AIM Module.

Thanks

Wael

Hall of Fame Super Gold

Re: 2port 2nd gen Multiflex trunk voice/wan int.T1/E1 Card with

Yes the card that you have can work in ATM mode but if you don't install the AIM-ATM, you cannot enter the ATM commands.

I've noticed that you haven't rated posts, would you consider doing so as an appreciation to those that are giving you free and good answers ?

452
Views
4
Helpful
8
Replies