Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

3640 CPU hog: 100% for hours. "RBSCP process " ?

Hello,

Recently I had an instance where a 3640 became unusable for about 3.5 hours.

The CPU was at 100%.

It appeared that the process "RBSCP Background" is the boooger that hogged the entire CPU's resource.

I find little information on the cisco.com site that explains this process. All I can find is information regarding a "Rate Based Satellite Control Protocol", however, this has never been used or configured. So not sure why the process is running and hogging.

All the information I have is this ...

Aug 1 21:19:12.471: %SYS-3-CPUHOG: Task is running for (12492)msecs, more than

(2000)msecs (3125/3124),process = RBSCP Background.

-Traceback= 0x604BBB50 0x604B98D8 0x604B9CB8 0x604C02C4

I am running Version 12.4(13b)

Any help or info on this process would be greatly appreciated ...

Many Thank

Matt

Also,

check out the CPU ... whooooow.

1

333666666669999999999969999999999999999999898998999909

345235442554888774424333433396615579767778899972915229989909

100 ** **############# **###*

90 ########**# *#################*******######

80 ########### ###################*#**########

70 ** ***#############################################

60 ***################################################

50 *##################################################

40 *##################################################

30 **####################################################

20 ######################################################

10 * *######################################################

0....5....1....1....2....2....3....3....4....4....5....5....6

0 5 0 5 0 5 0 5 0 5 0

CPU% per minute (last 60 minutes)

* = maximum CPU% # = average CPU%

111 1 111

00078877809765 515241990003

000141589044664182090130008

100 *** * ***

90 #** *** ***#*

80 ##* ******* ***#*

70 ##*********** ***#*

60 ##*******#**** **##*

50 ##*******#**** * * * **##*

40 ##*******#**** * * * **##**

30 ##*******#**** * * * **###*

20 ##*******#**** ***** **###*

10 ###**######### **#****####*

0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..

0 5 0 5 0 5 0 5 0 5 0 5 0

CPU% per hour (last 72 hours)

* = maximum CPU% # = average CPU%

4 REPLIES

Re: 3640 CPU hog: 100% for hours. "RBSCP process " ?

hi

can you paste the output of show rbscp all here ?

do u hve any tunnels enabled in your router ?

regds

New Member

Re: 3640 CPU hog: 100% for hours. "RBSCP process " ?

Hi,

Thanks for response.

Here's the output, basically nothing as its not running. Also, I can confirm there are no tunnels runnning. Its just three interfaces running in a very simple design (NO tunnels, NO dot1q tags, nothing)

Router#show rbscp all

Router#

Router#show rbscp statistics

Router#

Thanks

Matt

Re: 3640 CPU hog: 100% for hours. "RBSCP process " ?

Hi Matt

Is your CPU still hogging up ?

Also what about the RBSCP process utilisation now ?

Do you have any logs available with you during the hog up condition of your router ?

regds

New Member

Re: 3640 CPU hog: 100% for hours. "RBSCP process " ?

Hey,

Unfortunately not.

The cpu was crazy last night.

Its now settled down and is running fine.

CPU for RBSCP is now ...

Router#show proc cpu sorted | include RBSCP

94 414268 1392189 297 0.16% 0.14% 0.16% 0 RBSCP Background

Weired ...

The only log information I have is the CPU hog syslog msg and the traceback .. that's it.

I am stumped to why this service is being used and why this happened.

thanks

matt

304
Views
0
Helpful
4
Replies