Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

3GE-GBIC-SC: Unable to install 128 Packet Memory (4 x 128)

3GE-GBIC-SC NO. 1:

SLOT 4  (RP/LC 4 ): 3 Port Gigabit Ethernet

  MAIN: type 68,  800-6376-05 rev C0

        Deviation:  D063031, D062881, D048296

        HW config: 0x00    SW key: 00-00-00

  PCA:  73-4775-07 rev D0 ver 2

        Design Release 2.0  S/N XXXXXXXX

  MBUS: Embedded Agent

        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00

  DIAG: Test count: 0x00000000    Test results: 0x00000000

  FRU:  Linecard/Module: 3GE-GBIC-SC=

        Processor Memory: MEM-GRP/LC-128=

        Packet Memory: MEM-LC1-PKT-256=

  L3 Engine: 2 - Backbone OC48 (2.5 Gbps)

  MBUS Agent Software version 1.117 (RAM) (ROM version is 3.47)

  ROM Monitor version 16.12

  Fabric Downloader version used 10.1 (ROM version is 10.1)

  Primary clock is CSC 1

  Board is analyzed

  Board State is Line Card Enabled (IOS  RUN )

  Insertion time: 00:10:52 (00:03:03 ago)

  Processor Memory size: 134217728 bytes

  TX Packet Memory size: 134217728 bytes, Packet Memory pagesize: 8192 bytes

  RX Packet Memory size: 134217728 bytes, Packet Memory pagesize: 8192 bytes

  0 crashes since restart

3GE-GBIC-SC NO. 2:

SLOT 5  (RP/LC 5 ): 3 Port Gigabit Ethernet

  MAIN: type 68,  800-6376-01 rev E0

        Deviation: 0

        HW config: 0x00    SW key: 00-00-00

  PCA:  73-4775-02 rev E0 ver 2

        Design Release 2.0  S/N AAAAAAAA

  MBUS: Embedded Agent

        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00

  DIAG: Test count: 0x00000000    Test results: 0x00000000

  FRU:  Linecard/Module: 3GE-GBIC-SC=

        Processor Memory: MEM-GRP/LC-128=

        Packet Memory: MEM-PKT-512-UPG=

  L3 Engine: 2 - Backbone OC48 (2.5 Gbps)

  MBUS Agent Software version 1.117 (RAM) (ROM version is 2.32)

  ROM Monitor version 16.6

  Fabric Downloader version used 10.1 (ROM version is 10.1)

  Primary clock is CSC 1

  Board is analyzed

  Board State is Line Card Enabled (IOS  RUN )

  Insertion time: 00:05:11 (00:03:58 ago)

  Processor Memory size: 134217728 bytes

  TX Packet Memory size: 268435456 bytes, Packet Memory pagesize: 16384 bytes

  RX Packet Memory size: 268435456 bytes, Packet Memory pagesize: 16384 bytes

  0 crashes since restart

-------QUESTION-------
We tried to install the 6 packet memory modules of 3GE-GBIC-SC NO. 2 to 3GE-GBIC-SC NO. 1 but the 3GE-GBIC-SC NO. 1 did not sync with the GRP-B. It seems that 3GE-GBIC-SC NO. 1 does not accept any packet memory modules higher than 256MB. Do we have to upgrade the firmware/version of the hardware? If yes, kindly provide us the procedure or any link on how to do upgrade the hardware.
Thank you and regards,

  • WAN Routing and Switching
1 REPLY
Hall of Fame Super Silver

Re: 3GE-GBIC-SC: Unable to install 128 Packet Memory (4 x 128)

Hello Alfad,

I see that the linecard that accepts the 512 MB packet memory is version E0 and it is newer then the other one

also take in account memory chips location on engine2

http://www.cisco.com/en/US/docs/routers/12000/gsr_linecards/enet_lc/installation/guide/enet_lc.html#wp651093

check memory on linecards

http://www.cisco.com/en/US/docs/routers/12000/gsr_linecards/enet_lc/installation/guide/enet_lc.html#wp651420

3GE datashet says that packet memory can be upgraded to 512 MB regardless of version

http://www.cisco.com/en/US/products/hw/modules/ps2710/products_data_sheet09186a0080092085.html

so the version or revision should not be a problem

Hope to help

Giuseppe

747
Views
0
Helpful
1
Replies
This widget could not be displayed.