Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

7500 Slave RSP high CPU utilization problem

hello guyes

I have a problem about C-7513 Slave RSP high CPU utilization

I've configured for redundancy RSP configuration(SSO, RPR+ )

Router operated correctly.

But I can find HIgh CPU utiliztion on slave RSP(Standby) by 'IPC Slave CBus Process'

Active RSP CPU utilization is normal(0%).

So I want to fix this problem. but i can't find any solution.

somebody help me.

here is what i tried

1) changied IOS version,

- current IOS Version is RSP-K91PV-M Version 12.2(25)S15,

and I tried 12.4.23 (SP/VIP), 12.3.26(SP/VIP)

2) changeed redundancy mode

- RPR+, SSO(SSO mode supports only 12.2(25)S15 release

current RPR+ mode.

3) swaped RSP module

- swaped slot 6 with slot 7 (both are RSP 8)

here is slave RSP output.

#sh proc cp so

CPU utilization for five seconds: 96%/0%; one minute: 95%; five minutes: 95%

PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process

41 5543432 62852623 88 96.39% 95.67% 95.75% 0 IPC Slave CBus p

6 3548 684 5187 0.31% 0.06% 0.05% 0 Check heaps

1 0 5 0 0.00% 0.00% 0.00% 0 Chunk Manager

2 0 1160 0 0.00% 0.00% 0.00% 0 Load Meter

3 168 306 549 0.00% 0.03% 0.00% 0 Exec

4 0 26 0 0.00% 0.00% 0.00% 0 Retransmission o

5 4 44 90 0.00% 0.00% 0.00% 0 IPC ISSU Receive

7 0 1 0 0.00% 0.00% 0.00% 0 Pool Manager

8 0 2 0 0.00% 0.00% 0.00% 0 Timers

9 0 2 0 0.00% 0.00% 0.00% 0 Serial Backgroun

10 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager

11 0 5807 0 0.00% 0.00% 0.00% 0 OIR Handler

12 0 1139 0 0.00% 0.00% 0.00% 0 ALARM_TRIGGER_SC

13 0 97 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach

#sh redundancy

Redundant System Information :

------------------------------

Available system uptime = 1 hour, 41 minutes

Switchovers system experienced = 0

Hardware Mode = Duplex

Configured Redundancy Mode = rpr-plus

Operating Redundancy Mode = rpr-plus

Maintenance Mode = Disabled

Communications = Up

Current Processor Information :

-------------------------------

Standby Location = slot 7

Current Software state = STANDBY COLD-CONFIG

Uptime in current state = 1 hour, 36 minutes

Image Version = Cisco IOS Software, RSP Software (RSP-K91PV-M), Version 12.2(25)S15, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Fri 07-Dec-07 21:16 by tinhuang

BOOT = slot0:rsp-k91pv-mz.122-25.S15.bin,12;

CONFIG_FILE =

BOOTLDR = bootflash:rsp-boot-mz.124-23.bin

Configuration register = 0x102

Peer (slot: 6, state: ACTIVE) information is not available because this is the standby processor

1 REPLY
Hall of Fame Super Silver

Re: 7500 Slave RSP high CPU utilization problem

Hello ChangShik,

first of all verify that you have only VIP linecards in the chassis and no old cpuless Interface processors

see

RPR+ operates only in a system with VIPs as the line cards. Systems with legacy IPs default to RPR mode. Up to two legacy IPs can be supported by RPR+ if the service single-slot-reload-enable command is configured.

http://www.cisco.com/en/US/docs/ios/12_3t/12_3t7/feature/guide/gt_rpr2.html#wp1057189

Legacy IPs default to RPR. To allow RPR+ for VIPs when up to two legacy IPs exist in the router, you must configure the service single-slot-reload-enable command. If you do not enable the service single-slot-reload-enable command or if you have more than two legacy IPs, all the line cards are reloaded.

Hope to help

Giuseppe

180
Views
0
Helpful
1
Replies