Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

7609 RPS720 SUP issue.

Hi,

I have replaced my Cisco 7609's faulty RPS720 (RSP720-3C-GE)  with the new one on its module 5. After plugin the module into slot 5 , I am getting the below output. Since I am new to this series router, please suggest me how to configure this sup. ( Initially module 5 was Active and 6 was in standby)

RTR-2#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX    

  3    0  2-subslot Services SPA Carrier-400     7600-SSC-400     

  4    0  4-subslot SPA Interface Processor-200  7600-SIP-200      

5    0  Supervisor-Other                       Unknown            Unknown

  6    2  Route Switch Processor 720 (Active)    RSP720-3C-GE      

  7    0  4-subslot SPA Interface Processor-200  7600-SIP-200      

  8    0  4-subslot SPA Interface Processor-200  7600-SIP-200      

RTR-2#sh redundancy states

       my state = 13 -ACTIVE

     peer state = 1  -DISABLED

           Mode = Simplex

           Unit = Secondary

        Unit ID = 6

Redundancy Mode (Operational) = sso

Redundancy Mode (Configured)  = sso

Redundancy State              = Non Redundant

     Maintenance Mode = Disabled

Communications = Down      Reason: Simplex mode

   client count = 146

client_notification_TMR = 30000 milliseconds

          keep_alive TMR = 9000 milliseconds

        keep_alive count = 0

    keep_alive threshold = 18

           RF debug mask = 0x0

RTR-2#sh redundancy

Redundant System Information :

------------------------------

       Available system uptime = 1 week, 5 days, 13 hours, 45 minutes

Switchovers system experienced = 0

              Standby failures = 0

        Last switchover reason = none

                 Hardware Mode = Simplex

    Configured Redundancy Mode = sso

     Operating Redundancy Mode = sso

              Maintenance Mode = Disabled

                Communications = Down      Reason: Simplex mode

Current Processor Information :

-------------------------------

               Active Location = slot 6

        Current Software state = ACTIVE

       Uptime in current state = 1 week, 5 days, 13 hours, 45 minutes

                 Image Version = Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Thu 05-Aug-10 18:59 by prod_rel_team

                          BOOT =

                   CONFIG_FILE =

                       BOOTLDR =

        Configuration register = 0x2102

Peer (slot: unavailable) information is not available because it is in 'DISABLED' state


Regards,

Anil

  • WAN Routing and Switching
1 REPLY
Silver

7609 RPS720 SUP issue.

Hi,

The Supervisor on the Slot 5 might be on Rommon mode. Console into the Slot 5 Sup and try to boot it from there.

Thanks

Ankur

"Please rate the post if found useful"

289
Views
0
Helpful
1
Replies
This widget could not be displayed.