Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

7609 Switching Between RSP720 module

Dear all

 

I have problem with RSP720 backup module installed on Slot 5, all leds are in Ambar status. I am planning to plug it out and plug it in, trying to deterine if there is hardware issue. Compact flash is no inserted, I just inserted with IOS running on Slot6. I would like to know how to switch between module 6 and module 5. If those RSP720 are installed, one should be in ACTIVE status and the second one is STANDBY?

 

 

#sh module all
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    0  4-subslot SPA Interface Processor-400  7600-SIP-400       JAE13208UDD
  4   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1122QCWK
  5    0  Supervisor-Other                       Unknown            Unknown
  6    2  Route Switch Processor 720 (Active)    RSP720-3CXL-GE     JAE13030OMS
  9   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1122QAJY

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  0025.845a.5c40 to 0025.845a.5cbf   2.7   12.2(33)SRC4 12.2(33)SRC4 Ok
  4  001b.d45d.e2a0 to 001b.d45d.e2b7   2.6   12.2(14r)S5  12.2(33)SRC4 Ok
  5  0000.0000.0000 to 0000.0000.0000   0.0   Unknown      Unknown      Unknown
  6  001c.584c.b590 to 001c.584c.b593   5.7   12.2(33r)SRD 12.2(33)SRC4 Ok
  9  001b.d50e.4b10 to 001b.d50e.4b3f   2.5   12.2(14r)S5  12.2(33)SRC4 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
 1/0 2xGE SPA                    SPA-2X1GE          JAE1119G244  2.2    Ok
 1/1 2xGE SPA                    SPA-2X1GE          JAE1119G23T  2.2    Ok
  4  Centralized Forwarding Card WS-F6700-CFC       SAL1121PPGN  3.1    Ok
  6  Policy Feature Card 3       7600-PFC3CXL       JAE130316K6  1.0    Ok
  6  C7600 MSFC4 Daughterboard   7600-MSFC4         JAE13030T61  1.1    Ok
  9  Centralized Forwarding Card WS-F6700-CFC       SAL1121PPHH  3.1    Ok

Mod  Online Diag Status
---- -------------------
  1  Pass
 1/0 Pass
 1/1 Pass
  4  Pass
  5  Not Applicable
  6  Pass
  9  Pass

#sh module 6  
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  6    2  Route Switch Processor 720 (Active)    RSP720-3CXL-GE     JAE13030OMS

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  6  001c.584c.b590 to 001c.584c.b593   5.7   12.2(33r)SRD 12.2(33)SRC4 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  6  Policy Feature Card 3       7600-PFC3CXL       JAE130316K6  1.0    Ok
  6  C7600 MSFC4 Daughterboard   7600-MSFC4         JAE13030T61  1.1    Ok

Mod  Online Diag Status
---- -------------------
  6  Pass
7609-HE-CCS#sh module 5
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  5    0  Supervisor-Other                       Unknown            Unknown

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  5  0000.0000.0000 to 0000.0000.0000   0.0   Unknown      Unknown      Unknown

Mod  Online Diag Status
---- -------------------
  5  Not Applicable

 

 

2 ACCEPTED SOLUTIONS

Accepted Solutions

First of all connect to the

First of all connect to the console port of the RSP in slot 5 and hit Enter a couple of times in the terminal program that you're using.  If you get a "rommon>" prompt just send it the "boot" command - assuming the hardware is fine and nothing has happened to the RSP's IOS image, it should boot and become the stand-by supervisor for the chassis.  If that happens successfully you can then take a look at possible causes (like incorrect config register) of the RSP getting stuck in the ROM monitor...

"redundancy force-switchover"

"redundancy force-switchover" should turn the currently Hot supervisor Active

6 REPLIES

Maybe the RSP is stuck in

Maybe the RSP is stuck in ROMMON - attach a console to it, and if that's the case just "boot" it and you can debug the situation further after it's up (maybe somehow it lost the correct value of the config register)...

New Member

Dear IVAIDEANU, how can I

Dear IVAIDEANU, how can I boot RSP? Cisco 7609 is running and RSP Slot 6 is active, if I work with Slot 5 may cause issue on all system? Let me know which command can I apply for ROMMON status. Once is on active status, are those RSP active? or on in Active and the other one in STANBY?

First of all connect to the

First of all connect to the console port of the RSP in slot 5 and hit Enter a couple of times in the terminal program that you're using.  If you get a "rommon>" prompt just send it the "boot" command - assuming the hardware is fine and nothing has happened to the RSP's IOS image, it should boot and become the stand-by supervisor for the chassis.  If that happens successfully you can then take a look at possible causes (like incorrect config register) of the RSP getting stuck in the ROM monitor...

New Member

Hello IVAIDEANU, RSP is

Hello IVAIDEANU, RSP is working now:

7609-HE-CCS#show module all

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    0  4-subslot SPA Interface Processor-400  7600-SIP-400       JAE13208UDD

  4   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1122QCWK

  5    2  Route Switch Processor 720 (Hot)       RSP720-3CXL-GE     SAL1544UB9M

  6    2  Route Switch Processor 720 (Active)    RSP720-3CXL-GE     JAE13030OMS

  9   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1122QAJY

 

One more question. how can I turn active RSP Slot 6, in order to be sure that is OK, and Slot 5 in Hot status?

"redundancy force-switchover"

"redundancy force-switchover" should turn the currently Hot supervisor Active

New Member

Dear ivaideanu, thanks a lot

Dear ivaideanu, thanks a lot for your help, really usefull your support. Apreciated

Best Regards

 

 

291
Views
5
Helpful
6
Replies
CreatePlease login to create content