Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

877 router factory reset woes

Hi,

We've recently changed data line providers and now have some Cisco 877 routers we'd like to reconfigure and use at other sites. Although we own these, they were configured by our old data line providers, I'm having a hard time of resetting them to factory defaults and am after some advice.

The simple, hold down the reset button until it restarts does not work.

If I press the reset button within 5 seconds of power up to load the default rom image, I get the below:

System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2006 by cisco Systems, Inc.

C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory

Booting flash:c870-advipservicesk9-mz.124-24.T.bin

Error opening: flash:c870-advipservicesk9-mz.124-24.T.bin

System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2006 by cisco Systems, Inc.

C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory

Booting flash:/c870-advsecurityk9-mz.124-24.T6.bin

Self decompressing the image : ############################################################################## [OK]

I assume from this the required bin has either been removed, renamed or overwritten.

As soon as the router boots it requires a password and I dont have the password to be able ftp files in and out of it.

Hope you guys can help.

Thanks,

Damien.

1 ACCEPTED SOLUTION

Accepted Solutions
Purple

877 router factory reset woes

Hi,

this should work indeed.

take a look here:http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080174a34.shtml

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.
10 REPLIES
Hall of Fame Super Gold

877 router factory reset woes

Have searched "router password recovery" here or on cisco.com ?

New Member

Re: 877 router factory reset woes

Hi Paolo, thanks for the response, yes I have as well as being familiar with cisco password recovery techniques from previous experience. In this scenario it looks like i should be using the rom monitor prompt but I am unable to access it by using the break within 60 seconds of a hard reboot.

Purple

Re: 877 router factory reset woes

Hi,

which terminal emulator software are you using to connect to the router  and which keys are you using as break sequence ?

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.
New Member

Re: 877 router factory reset woes

Hi Alain, I'm using PuTTY

New Member

Re: 877 router factory reset woes

and CTRL Break, apologies forgot to add that bit.

Purple

877 router factory reset woes

Hi,

this should work indeed.

take a look here:http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080174a34.shtml

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.
Hall of Fame Super Gold

877 router factory reset woes

If you are using an USB / serial adapter, replace it with one of reputable maker, that is able to send ctrl-break.

Hall of Fame Super Gold

877 router factory reset woes

877 right?  Look at the back of the router.  There should be a tiny "Reset" button.  Have you tried that?

Hall of Fame Super Gold

877 router factory reset woes

leolaohoo wrote:

877 right?  Look at the back of the router.  There should be a tiny "Reset" button.  Have you tried that?

Yes Leo, he did as mentioned in the first pst.

New Member

Re: 877 router factory reset woes

Hi Alain/Paolo

I got in to the rommon in the end, I needed to configure a special command for the ctrl+break command in PuTTY as CTRL+Break alone was not working.

Thanks for the help.

7993
Views
0
Helpful
10
Replies
CreatePlease login to create content