Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

887VA VDSL2 configuration

Hi

I have a Cisco 887VA router that I'm trying to connect to a VDSL2 service.

I'm getting this error when the VDSL2 service is plugged in:

%VDSL_DAEMON-4-TRAINMODE_NOT_SUPPORTED: ATM transport mode is not supported on VDSL2.

Here is the controller details:

Controller VDSL 0 is DOWN

Daemon Status:           Establishing Link

                        XTU-R (DS)              XTU-C (US)

Chip Vendor ID:         'BDCM'                   'BDCM'

Chip Vendor Specific:   0x0000                   0x939B

Chip Vendor Country:    0xB500                   0xB500

Modem Vendor ID:        'CSCO'                   '    '

Modem Vendor Specific:  0x4602                   0x0000

Modem Vendor Country:   0xB500                   0x0000

Serial Number Near:     887VA-M- 15.1(4)M 

Serial Number Far:    

Modem Version Near:    15.1(4)M

Modem Version Far:     0x939b

Modem Status:            Idle

DSL Config Mode:         VDSL2

Trained Mode:            

TC Mode:                 ATM

Selftest Result:         0x00

DELT configuration:      disabled

DELT state:              not running

Trellis:                 ON

Heres is the config:

interface Ethernet0

description $ETH-WAN$

ip address dhcp

ip tcp adjust-mss 1412

pppoe-client dial-pool-number 1

!

interface ATM0

no ip address

no atm ilmi-keepalive

shutdown

!

interface Vlan1

description LAN

ip address 10.0.0.20 255.0.0.0

ip nat inside

ip virtual-reassembly in

ip tcp adjust-mss 1412

!

interface Dialer1

description Dialer interface for VDSL

mtu 1492

ip address negotiated

no ip redirects

no ip unreachables

no ip proxy-arp

ip mtu 1452

ip nbar protocol-discovery

ip flow ingress

ip nat outside

ip virtual-reassembly in

encapsulation ppp

ip tcp adjust-mss 1452

dialer pool 1

ppp authentication pap chap ms-chap callin

ppp chap hostname *********

ppp chap password 0 *******

ppp ipcp address accept

no cdp enable

!

ip nat inside source list NAT interface Dialer1 overload

ip route 0.0.0.0 0.0.0.0 Dialer1

!

ip access-list extended nat

permit ip 10.0.0.0 0.255.255.255 any

remark Access list for NAT

!

dialer-list 1 protocol ip permit

Everyone's tags (1)
8 REPLIES
Hall of Fame Super Gold

887VA VDSL2 configuration

Interface can't train up, try another router for verification or check with telco.

Community Member

887VA VDSL2 configuration

I don't have another cisco router with a vdsl interface, i have tested the basic router that was provided by my ISP and that connects fine.

Hall of Fame Super Gold

887VA VDSL2 configuration

That's what I meant, try updating IOS and/or VDSL firmware. Worst case you have to use ISP router in bridge mode and cisco PPPoE on Vlan interface.

Bronze

FWIW...

FWIW...

I have an 887VA and VDSL2 (PTM) from an ISP working.

They don't use PPPoE so I'm not sure this will help any that require it. 

All I had to stop using ATM interfaces and use interface E0

(no subinterface as recommended elsewhere) and then

controller vdsl 0

operating mode vdls2

Community Member

887VA VDSL2 configuration

Try:

conf t

wan mode ethernet

exit

controller vdsl operating mode auto

Community Member

887VA VDSL2 configuration

I have updated the VDSL firmware and am now getting

%VDSL_DAEMON-4-TRAINMODE_NOT_SUPPORTED: UNKNOWN transport mode is not supported on VDSL2.

I have changed the vdsl operating mode to auto, but the "wan mode ethernet" isn't a recognized command

Hall of Fame Super Gold

887VA VDSL2 configuration

That is not an error just a warning and is not related to the problem.

Unless you can get Cisco Tac into looking why the router doesn;t sync with the particular ISP DLSAM, you will need to use the ISP router as mentioned above.

Community Member

887VA VDSL2 configuration

I have finally got it working, my ISP sent an engineer and he fixed it in 2 minutes.

My ISP uses VDSL2 over PPPoA and apart from the cheap router they supply no other router supports this, they changed my line to PPPoE from the MSAN and it connected.

10887
Views
0
Helpful
8
Replies
CreatePlease to create content