Cisco Support Community
Showing results for 
Search instead for 
Did you mean: 
Community Member

adsl_alc_20190_6.0.010.bin firmware on Cisco 877W

Hello all,

I've got Cisco 877W but it didn't like when I applied what I think is the last firmware for ST Micro -


Any suggestions?

Many thanks


My version:

#show ver

Cisco IOS Software, C870 Software (C870-ADVIPSERVICESK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)

Compiled Wed 21-Mar-12 00:53 by prod_rel_team

ROM: System Bootstrap, Version 12.3(8r)YI3, RELEASE SOFTWARE

System returned to ROM by reload at 10:42:22 GMT Fri Mar 1 2002

System restarted at 13:58:35 BST Tue Oct 1 2013

System image file is "flash:c870-advipservicesk9-mz.151-4.M4.bin"

Last reload reason: Reload Command

Cisco 877W (MPC8272) processor (revision 2.0) with 236544K/25600K bytes of memory.

Processor board ID FCZ105123PM

MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10

4 FastEthernet interfaces

1 ATM interface

1 Virtual Private Network (VPN) Module

1 802.11 Radio

128K bytes of non-volatile configuration memory.

53248K bytes of processor board System flash (Intel Strataflash)

Configuration register is 0x2102

with the adsl_alc_20190_6.0.010.bin :

#show dsl int


Alcatel 20190 chipset information

Line has not yet been activated.

Modem Status:           Down (DMTDSL_DO_OPEN)

DSL Mode:           Unknown

Interrupts:           37291 (0 spurious)

PHY Access Err:           0

Activations:           0

LED Status:           ON

LED On Time:           100

LED Off Time:           100

Init FW:           init_AMR_6.0.010.bin

Operation FW:           AMR-E-6.0.010.bin

FW Source:           external

DSL: Training log buffer capability is not enabled

with the original 4.0.015 firware:

#show dsl int


Alcatel 20190 chipset information

                     ATU-R (DS)                              ATU-C (US)

Modem Status:           Showtime (DMTDSL_SHOWTIME)

DSL Mode:           ITU G.992.3 (ADSL2) Annex A

ITU STD NUM:            0x03                                         0x2

Chip Vendor ID:           'STMI'                                         'IFTN'

Chip Vendor Specific:  0x0000                               0x71C8

Chip Vendor Country:   0x0F                               0xB5

Modem Vendor ID: 'CSCO'                                         '    '

Modem Vendor Specific: 0x0000                               0x0000

Modem Vendor Country:  0xB5                               0x00

Serial Number Near:    FCZ105123P 877W-G-E 15.1

Serial Number Far:  Chip ID:            C196 (0)

DFE BOM:           DFE3.0 Annex A (1)

Capacity Used:           99%                                         100%

Noise Margin:            5.5 dB                                6.0 dB

Output Power:           16.0 dBm                               12.5 dBm

Attenuation:           61.0 dB                               38.0 dB

FEC ES Errors:            0                                          0

ES Errors:           11                                          0

SES Errors:            1                                          0

LOSES Errors:            1                                          0

UES Errors:            0                                         43

Defect Status:           None                            None                       

Last Fail Code:           None

Watchdog Counter: 0xEB

Watchdog Resets: 0

Selftest Result: 0x00

Subfunction:           0x00

Interrupts:           4201 (0 spurious)

PHY Access Err:           0

Activations:           1

LED Status:           ON

LED On Time:           100

LED Off Time:           100

Init FW:           init_AMR-4.0.015_no_bist.bin

Operation FW:           AMR-4.0.015.bin

FW Source:           embedded

FW Version:           4.0.15

Hall of Fame Super Gold

Re: adsl_alc_20190_6.0.010.bin firmware on Cisco 877W

[edited due to incorrect information]      

Community Member

Re: adsl_alc_20190_6.0.010.bin firmware on Cisco 877W

I see. I assume you're refering to the ADSL firware.

Well, I've got this one from Cisco

and therefore I would assume it is recomended, if anything, to use it.

I would be surprise if Cisco put on their own web something what is not official and should not be used, but I could be wrong.

Thank you for your help


CreatePlease to create content